ASVAB Practice Exam 4

Last updated: October 31, 2026

Practice Exam 4 is a fixed set of 135 original questions in the same 10 subtests, order, and time limits as the computer ASVAB. Take it timed, one question at a time, or read through the questions below. Each answer is explained.

Pick the length

Study mode is on: each answer is explained. Switch it off inside the test for real exam conditions.
Same order, question counts, and time limits as the CAT-ASVAB
#SubtestQuestionsMinutes
1General Science GS1512
2Arithmetic Reasoning AR1555
3Word Knowledge WK159
4Paragraph Comprehension PC1027
5Mathematics Knowledge MK1531
6Electronics Information EI1510
7Auto Information AI107
8Shop Information SI106
9Mechanical Comprehension MC1522
10Assembling Objects AO1518

All 135 questions in Practice Exam 4

Taking the timed test first gives you the truest read. It serves these same questions one at a time, adjusting the order to your answers. To study instead, work through them here: each answer and explanation is folded under its question.

General Science: 15 questions

Physical, life, and earth and space science. Real test: 15 questions in 12 minutes.

  1. Which organs filter wastes out of the blood and remove them from the body in urine?

    1. Athe lungs
    2. Bthe liver
    3. Cthe kidneys
    4. Dthe stomach
    Show answer and explanation

    Answer: C. The kidneys filter the blood, keep what the body needs, and send wastes and extra water to the bladder as urine.

    • AWrong. The lungs remove carbon dioxide from the blood when you breathe out; they do not make urine.
    • BWrong. The liver breaks down toxins and old blood cells, but it sends wastes out in bile and through the kidneys, not as urine itself.
    • CCorrect. The kidneys filter the blood, keep what the body needs, and send wastes and extra water to the bladder as urine.
    • DWrong. The stomach mixes food with acid to begin digestion; it does not filter the blood.
  2. Which material is the best conductor of electricity?

    1. Arubber
    2. Bglass
    3. Cwood
    4. Dcopper
    Show answer and explanation

    Answer: D. Metals such as copper have electrons that move freely, so current flows through them easily. That is why most electrical wire is copper.

    • AWrong. Rubber holds its electrons tightly, so it blocks current; it is used to insulate wires and tool handles.
    • BWrong. Glass is an insulator; it is used to make some of the insulators that hold up power lines.
    • CWrong. Dry wood is a poor conductor, though it can carry current when wet or dirty; it is nowhere near as good a conductor as a metal.
    • DCorrect. Copper, a metal, has electrons that move freely, so current flows through it easily; most electrical wire is copper.
  3. Which blood vessels carry blood away from the heart?

    1. AVeins
    2. BArteries
    3. CCapillaries
    4. DLymph vessels
    Show answer and explanation

    Answer: B. Arteries carry blood away from the heart; veins bring it back.

    • AWrong. Veins carry blood back toward the heart.
    • BCorrect. Arteries carry blood away from the heart under high pressure, which is why they have thick, muscular walls.
    • CWrong. Capillaries are the tiny vessels between arteries and veins where oxygen, nutrients, and wastes pass to and from body cells.
    • DWrong. Lymph vessels carry lymph, fluid drained from the tissues, back toward the bloodstream; they do not carry blood from the heart.
  4. In adults, most red blood cells are made in the

    1. Abone marrow.
    2. Bliver.
    3. Cspleen.
    4. Dlymph nodes.
    Show answer and explanation

    Answer: A. Soft tissue inside bones, the bone marrow, produces red blood cells, white blood cells, and platelets throughout adult life.

    • ACorrect. Soft tissue inside bones, the bone marrow, produces red blood cells, white blood cells, and platelets throughout adult life.
    • BWrong. The liver makes red blood cells before birth, but in adults it recycles the parts of worn-out red cells instead.
    • CWrong. The spleen filters the blood and removes old, damaged red blood cells; it does not make most new ones.
    • DWrong. Lymph nodes filter lymph and house white blood cells that fight infection; they do not make red blood cells.
  5. Plant cells have a stiff outer layer that animal cells lack. This layer is called the

    1. Acell membrane.
    2. Bcell wall.
    3. Ccytoplasm.
    4. Dnucleus.
    Show answer and explanation

    Answer: B. The cell wall, made mostly of cellulose, surrounds the membrane of a plant cell and gives it a firm shape. Animal cells have no cell wall.

    • AWrong. Both plant and animal cells have a cell membrane; in plant cells it lies just inside the cell wall.
    • BCorrect. The cell wall, made mostly of cellulose, surrounds the membrane of a plant cell and gives it a firm shape; animal cells have none.
    • CWrong. Cytoplasm is the jelly-like material that fills the inside of both plant and animal cells, not an outer layer.
    • DWrong. The nucleus holds the cell’s DNA and sits inside the cell; animal cells have one too.
  6. Which of these substances is a compound?

    1. Aoxygen gas (O₂)
    2. Biron (Fe)
    3. Ctable salt (NaCl)
    4. Dhelium (He)
    Show answer and explanation

    Answer: C. A compound is made of two or more different elements chemically joined. Table salt is sodium and chlorine bonded together.

    • AWrong. Oxygen gas is a molecule of two oxygen atoms, but only one element, so it is an element, not a compound.
    • BWrong. Iron is a pure element made of only one kind of atom.
    • CCorrect. Table salt is sodium and chlorine, two different elements chemically joined, which makes it a compound.
    • DWrong. Helium is an element whose atoms exist alone, not bonded to any other element.
  7. Clouds form when water vapor in rising air cools and turns into tiny liquid droplets. This change is called

    1. Acondensation.
    2. Bevaporation.
    3. Cprecipitation.
    4. Dtranspiration.
    Show answer and explanation

    Answer: A. Condensation is the change from a gas (water vapor) to a liquid. Cooling air holds less vapor, so droplets form and make clouds.

    • ACorrect. Condensation is the change from a gas to a liquid; cooling vapor forms the droplets that make up clouds.
    • BWrong. Evaporation is the opposite change, liquid water turning into vapor, which puts the moisture into the air in the first place.
    • CWrong. Precipitation is water falling from clouds as rain, snow, sleet, or hail, after the droplets have already formed.
    • DWrong. Transpiration is water vapor given off by plants through their leaves, not vapor turning into droplets.
  8. The main cause of the seasons on Earth is

    1. Athe tilt of Earth’s axis.
    2. BEarth’s changing distance from the Sun.
    3. Cthe Moon’s pull on Earth.
    4. Dchanges in the Sun’s energy output.
    Show answer and explanation

    Answer: A. Earth’s axis is tilted about 23.5°, so each hemisphere gets more direct sunlight and longer days while it leans toward the Sun.

    • ACorrect. Earth’s axis is tilted about 23.5°, so each hemisphere gets more direct sunlight and longer days while it leans toward the Sun.
    • BWrong. Earth’s distance from the Sun changes only about 3%, and Earth is closest in early January, during Northern Hemisphere winter.
    • CWrong. The Moon’s pull does not change how much sunlight reaches either hemisphere, so it cannot bring summer and winter.
    • DWrong. The Sun’s energy output changes by only about 0.1%, far too little to cause seasons.
  9. Carbon dioxide enters a leaf, and oxygen and water vapor leave it, mainly through tiny openings called

    1. Astomata.
    2. Bxylem.
    3. Croot hairs.
    4. Dchloroplasts.
    Show answer and explanation

    Answer: A. Stomata are small pores, mostly on the underside of leaves, that open and close to let gases in and out.

    • ACorrect. Stomata are small pores, mostly on the underside of leaves, that open and close to let gases in and out.
    • BWrong. Xylem is the tissue that carries water up from the roots to the leaves; it is not an opening to the air.
    • CWrong. Root hairs are thin growths on roots that take in water and minerals from the soil, not gases from the air.
    • DWrong. Chloroplasts are the structures inside leaf cells where photosynthesis happens; gases reach them through the stomata.
  10. How much work is done lifting a box that weighs 50 newtons straight up a distance of 2 meters?

    1. A25 J
    2. B52 J
    3. C100 J
    4. D980 J
    Show answer and explanation

    Answer: C. Work = force × distance. Lifting takes a force equal to the weight: 50 N × 2 m = 100 J.

    • AWrong. 25 J divides the force by the distance (50 ÷ 2); work is force times distance.
    • BWrong. 52 J adds the force and the distance (50 + 2); work is force times distance.
    • CCorrect. Work = force × distance, and lifting takes a force equal to the weight: 50 N × 2 m = 100 J.
    • DWrong. 980 J also multiplies by 9.8, but 50 newtons is already a weight (a force), so g is not needed again.
  11. Geologists rank minerals from 1 (talc) to 10 (diamond) by which mineral can scratch which. This ranking is called the

    1. ApH scale.
    2. BRichter scale.
    3. CBeaufort scale.
    4. DMohs scale.
    Show answer and explanation

    Answer: D. The Mohs scale ranks mineral hardness: a mineral scratches any mineral with a lower number, and diamond, at 10, is the hardest.

    • AWrong. The pH scale measures how acidic or basic a solution is, from 0 to 14.
    • BWrong. The Richter scale was made to measure the size of earthquakes, not the hardness of minerals.
    • CWrong. The Beaufort scale estimates wind speed from what the wind does to waves, trees, and flags.
    • DCorrect. The Mohs scale ranks mineral hardness: a mineral scratches any mineral lower on the scale, and diamond, at 10, is the hardest.
  12. Isotopes of the same element have different numbers of

    1. Aprotons.
    2. Belectrons.
    3. Cneutrons.
    4. Denergy levels.
    Show answer and explanation

    Answer: C. Isotopes have the same number of protons (so they are the same element) but different numbers of neutrons, as in carbon-12 and carbon-14.

    • AWrong. Atoms with different numbers of protons are different elements, not isotopes of one element.
    • BWrong. An atom that gains or loses electrons becomes an ion, not a different isotope.
    • CCorrect. Isotopes share the same number of protons but differ in neutrons, so their masses differ, as with carbon-12 and carbon-14.
    • DWrong. Isotopes of an element have the same electron arrangement, which is why they react alike chemically.
  13. One strand of a DNA molecule has the bases A-T-T-G-C. Which sequence of bases lines up opposite it on the other strand?

    1. AA-T-T-G-C
    2. BG-C-C-A-T
    3. CT-A-A-C-G
    4. DU-A-A-C-G
    Show answer and explanation

    Answer: C. In DNA, A always pairs with T and G always pairs with C, so A-T-T-G-C pairs with T-A-A-C-G.

    • AWrong. A-T-T-G-C copies the first strand; each base pairs with a different partner, not with itself.
    • BWrong. G-C-C-A-T pairs A with G and T with C, but in DNA A pairs with T and G pairs with C.
    • CCorrect. A pairs with T and G pairs with C, so A-T-T-G-C lines up with T-A-A-C-G.
    • DWrong. U-A-A-C-G uses uracil, which is found in RNA; DNA uses thymine (T) to pair with A.
  14. A thermometer reads 25 °C. What is this temperature in degrees Fahrenheit?

    1. A14 °F
    2. B45 °F
    3. C57 °F
    4. D77 °F
    Show answer and explanation

    Answer: D. °F = (°C × 9/5) + 32. 25 × 9/5 = 45, and 45 + 32 = 77 °F.

    • AWrong. 14 °F multiplies by 5/9 instead of 9/5 and leaves out the 32.
    • BWrong. 45 °F multiplies by 9/5 correctly but forgets to add 32.
    • CWrong. 57 °F adds 32 but skips multiplying by 9/5.
    • DCorrect. °F = (°C × 9/5) + 32, so 25 × 9/5 = 45 and 45 + 32 = 77 °F.
  15. The producers in a food chain capture 20,000 kilocalories of energy from sunlight. About how much of that energy is likely to reach the secondary consumers?

    1. A20 kcal
    2. B200 kcal
    3. C2,000 kcal
    4. D10,000 kcal
    Show answer and explanation

    Answer: B. Only about 10% of the energy at one level passes to the next. Primary consumers get about 2,000 kcal, and secondary consumers get about 10% of that, or 200 kcal.

    • AWrong. 20 kcal is about what would reach the tertiary consumers, one level higher (three steps of 10%).
    • BCorrect. About 10% passes up each level: 20,000 to about 2,000 for primary consumers, then about 200 kcal for secondary consumers.
    • CWrong. 2,000 kcal is about what reaches the primary consumers, the plant eaters, one level lower.
    • DWrong. 10,000 kcal assumes half the energy passes on; most is used for life processes or lost as heat, so only about 10% moves up.

Arithmetic Reasoning: 15 questions

Word problems solved with arithmetic. No calculator; use scratch paper. Real test: 15 questions in 55 minutes.

  1. A warehouse had 1,250 boxes of paper. During one week, 375 boxes were shipped out. How many boxes are left in the warehouse?

    1. A625
    2. B875
    3. C885
    4. D1,125
    Show answer and explanation

    Answer: B. 1,250 − 375 = 875.

    • AWrong. 625 subtracts 375 from 1,000 and leaves out the other 250 boxes.
    • BCorrect. 1,250 − 375 = 875 boxes left.
    • CWrong. 885 forgets to reduce the tens digit after borrowing from it for the ones place.
    • DWrong. 1,125 subtracts the smaller digit from the larger in each column instead of borrowing.
  2. A pizza is cut into 12 equal slices. A family eats 3/4 of the pizza. How many slices does the family eat?

    1. A3
    2. B4
    3. C9
    4. D16
    Show answer and explanation

    Answer: C. 3/4 of 12 = (12 ÷ 4) × 3 = 9 slices.

    • AWrong. 3 is 1/4 of the pizza, which is the part left over, not the part eaten.
    • BWrong. 4 divides 12 by 3, which finds 1/3 of the pizza instead of 3/4.
    • CCorrect. 12 ÷ 4 = 3 slices in each fourth, and 3 fourths is 3 × 3 = 9 slices.
    • DWrong. 16 divides 12 by 3/4. Finding a fraction of a number means multiplying by it.
  3. One customer buys 3 shirts at $14 each. Another customer buys 2 pairs of pants at $27 each. How much more does the second customer spend than the first?

    1. A$12
    2. B$13
    3. C$54
    4. D$96
    Show answer and explanation

    Answer: A. The first customer spends 3 × $14 = $42. The second spends 2 × $27 = $54. $54 − $42 = $12.

    • ACorrect. 3 × $14 = $42 and 2 × $27 = $54, so the second customer spends $54 − $42 = $12 more.
    • BWrong. $13 is the difference between one pair of pants and one shirt ($27 − $14). It ignores how many of each were bought.
    • CWrong. $54 is what the second customer spends in all, not how much more than the first.
    • DWrong. $96 adds the two totals ($42 + $54). The question asks for the difference.
  4. A rectangular garden is 15 feet long and 8 feet wide. Sod costs $2 per square foot. How much will it cost to cover the garden with sod?

    1. A$46
    2. B$92
    3. C$120
    4. D$240
    Show answer and explanation

    Answer: D. Area = 15 × 8 = 120 square feet. 120 × $2 = $240.

    • AWrong. $46 adds the length and width (23) and doubles it. That is the perimeter in feet, not a cost based on area.
    • BWrong. $92 multiplies the perimeter (46 feet) by $2. Sod covers area, so use length × width.
    • CWrong. $120 is the area in square feet. It still has to be multiplied by $2 per square foot.
    • DCorrect. The area is 15 × 8 = 120 square feet, and 120 × $2 = $240.
  5. In a class of 48 students, 3/8 ride the bus to school and 1/3 walk. The rest ride in a car. How many students ride in a car?

    1. A14
    2. B16
    3. C30
    4. D34
    Show answer and explanation

    Answer: A. 3/8 of 48 = 18 ride the bus and 1/3 of 48 = 16 walk. 48 − 18 − 16 = 14 ride in a car.

    • ACorrect. 3/8 of 48 = 18 ride the bus and 1/3 of 48 = 16 walk. 48 − 18 − 16 = 14 ride in a car.
    • BWrong. 16 is the number who walk, not the number who ride in a car.
    • CWrong. 30 takes away only the 18 bus riders. The 16 walkers must also come off.
    • DWrong. 34 is the bus riders plus the walkers. It still has to be subtracted from 48.
  6. A carpenter cuts 4 shelves, each 2 feet 8 inches long, from a board that is 12 feet long. How much of the board is left?

    1. A1 foot 4 inches
    2. B2 feet 8 inches
    3. C3 feet 4 inches
    4. D10 feet 8 inches
    Show answer and explanation

    Answer: A. Each shelf is 32 inches, so 4 shelves use 128 inches. The board is 144 inches, and 144 − 128 = 16 inches, or 1 foot 4 inches.

    • ACorrect. 4 × 32 inches = 128 inches used. 144 − 128 = 16 inches, which is 1 foot 4 inches.
    • BWrong. 2 feet 8 inches comes from subtracting 10 feet 8 inches by doing 12 − 10 for the feet and 8 − 0 for the inches. A foot has to be borrowed: 12 feet = 11 feet 12 inches.
    • CWrong. 3 feet 4 inches multiplies only the feet by 4 (8 feet) and adds the 8 inches once, so it counts just 8 feet 8 inches of shelving.
    • DWrong. 10 feet 8 inches is the length used for the shelves, not the length left over.
  7. At a park cleanup, 3/5 of the volunteers are adults and the rest are children. If 18 of the volunteers are children, how many volunteers are there in all?

    1. A27
    2. B30
    3. C36
    4. D45
    Show answer and explanation

    Answer: D. Children are 1 − 3/5 = 2/5 of the group. If 2/5 of the total is 18, then 1/5 is 9 and the total is 5 × 9 = 45.

    • AWrong. 27 is the number of adults (3/5 of 45), not the total.
    • BWrong. 30 treats the 18 children as 3/5 of the group. The 3/5 are the adults; children are 2/5.
    • CWrong. 36 doubles 18, as if the children were half the group instead of 2/5.
    • DCorrect. Children are 2/5 of the group, so 1/5 is 18 ÷ 2 = 9 and the whole group is 5 × 9 = 45.
  8. A club has $500 to spend on a banquet. The hall charges a $120 fee, and each meal costs $16. What is the greatest number of meals the club can buy?

    1. A7
    2. B23
    3. C24
    4. D31
    Show answer and explanation

    Answer: B. After the fee, $500 − $120 = $380 is left. $380 ÷ $16 = 23.75, and the club cannot buy part of a meal, so 23.

    • AWrong. 7 divides the $120 hall fee by $16. The fee is subtracted from the budget, not divided.
    • BCorrect. $500 − $120 = $380, and $380 ÷ $16 = 23.75. Only whole meals can be bought, so the most is 23.
    • CWrong. 24 rounds 23.75 up, but 24 meals cost $384, which is more than the $380 left after the fee.
    • DWrong. 31 divides the full $500 by $16 and forgets to pay the $120 hall fee first.
  9. Six workers can build a fence in 10 days. Working at the same rate, how many days would it take 4 workers to build the same fence?

    1. A6 2/3
    2. B8
    3. C12
    4. D15
    Show answer and explanation

    Answer: D. The job takes 6 × 10 = 60 worker-days. 60 ÷ 4 workers = 15 days.

    • AWrong. 6 2/3 treats fewer workers as fewer days (10 × 4/6). With fewer workers the job takes longer, not shorter.
    • BWrong. 8 subtracts the 2 missing workers from 10 days. Days do not change by the same number as workers.
    • CWrong. 12 adds the 2 missing workers to 10 days. The job is 60 worker-days, so 4 workers need 60 ÷ 4 = 15 days.
    • DCorrect. 6 workers × 10 days = 60 worker-days of work. 4 workers need 60 ÷ 4 = 15 days.
  10. A town's library had 200 members last year. This year it has 250 members. By what percent did the number of members increase?

    1. A20%
    2. B25%
    3. C50%
    4. D125%
    Show answer and explanation

    Answer: B. The increase is 250 − 200 = 50. 50 ÷ 200 (the original number) = 0.25 = 25%.

    • AWrong. 20% divides the increase by the new number (50 ÷ 250). Percent change is measured from the original number, 200.
    • BCorrect. The increase is 50, and 50 ÷ 200 = 0.25, which is 25%.
    • CWrong. 50% uses the increase of 50 members as if it were the percent.
    • DWrong. 125% is this year's membership as a percent of last year's (250 ÷ 200). The increase is 25%.
  11. The price of a can of paint went up from $40 to $50. Later the price went back down to $40. By what percent did the price go down?

    1. A10%
    2. B20%
    3. C25%
    4. D80%
    Show answer and explanation

    Answer: B. The drop is $10, measured from the $50 price before the drop: 10 ÷ 50 = 1/5 = 20%.

    • AWrong. 10% uses the $10 change as the percent. It has to be divided by the starting price of $50.
    • BCorrect. The drop is $10, measured from the $50 price before the drop: 10 ÷ 50 = 1/5 = 20%.
    • CWrong. 25% divides the $10 drop by $40. That was the percent of the increase; the decrease starts from $50.
    • DWrong. 80% is the new price as a percent of $50, the part that remains, not the decrease.
  12. A jar holds red and blue marbles in a ratio of 3 to 5. After 12 red marbles are added, the jar holds equal numbers of red and blue marbles. How many marbles were in the jar before the red marbles were added?

    1. A32
    2. B48
    3. C60
    4. D96
    Show answer and explanation

    Answer: B. Let red = 3k and blue = 5k. After adding 12 red, 3k + 12 = 5k, so k = 6. The jar held 18 red + 30 blue = 48 marbles.

    • AWrong. 32 treats the 12 added marbles as 3 parts (k = 4). The 12 marbles make up the gap between 5 parts and 3 parts, which is 2 parts.
    • BCorrect. 3k + 12 = 5k gives k = 6, so the jar held 18 red and 30 blue, 48 in all.
    • CWrong. 60 is the number of marbles after the 12 red ones were added, not before.
    • DWrong. 96 treats 12 marbles as one part of the ratio, then multiplies by all 8 parts.
  13. A truck leaves a warehouse at 8:00 a.m. and drives at 45 miles per hour. At 9:00 a.m., a car leaves the same warehouse and follows the same road at 60 miles per hour. At what time does the car catch up with the truck?

    1. A9:45 a.m.
    2. B11:00 a.m.
    3. C12:00 noon
    4. D1:00 p.m.
    Show answer and explanation

    Answer: C. At 9:00 the truck is 45 miles ahead. The car gains 60 − 45 = 15 miles each hour, so it needs 45 ÷ 15 = 3 hours. 9:00 a.m. + 3 hours = 12:00 noon.

    • AWrong. 9:45 a.m. is how long the car takes to drive 45 miles (45 ÷ 60 = 3/4 hour), but the truck keeps moving during that time.
    • BWrong. 11:00 a.m. adds the 3-hour catch-up time to 8:00 a.m. The car does not start until 9:00 a.m.
    • CCorrect. The truck has a 45-mile lead at 9:00, and the car closes the gap at 15 miles per hour: 45 ÷ 15 = 3 hours, so noon.
    • DWrong. 1:00 p.m. divides 60 by 15 to get 4 hours. The gap to close is the truck's 45-mile lead, not 60 miles.
  14. One class of 20 students averaged 76 points on a test. Another class of 30 students averaged 86 points on the same test. What was the average score for all 50 students?

    1. A80
    2. B81
    3. C82
    4. D162
    Show answer and explanation

    Answer: C. Total points: 20 × 76 = 1,520 and 30 × 86 = 2,580, which is 4,100. 4,100 ÷ 50 = 82.

    • AWrong. 80 swaps the class sizes, giving 30 students the 76 average. The larger class had the higher average.
    • BWrong. 81 averages 76 and 86 as if the classes were the same size. The class of 30 counts more.
    • CCorrect. Total points: 20 × 76 = 1,520 and 30 × 86 = 2,580, which is 4,100. 4,100 ÷ 50 = 82.
    • DWrong. 162 adds the two averages and never divides.
  15. A bicycle wheel has a diameter of 21 inches. How many complete turns does the wheel make when the bicycle travels 1 mile? (Use π = 22/7 and 1 mile = 5,280 feet.)

    1. A80
    2. B480
    3. C960
    4. D3,017
    Show answer and explanation

    Answer: C. One turn covers the circumference: 22/7 × 21 = 66 inches. 1 mile = 5,280 × 12 = 63,360 inches. 63,360 ÷ 66 = 960 turns.

    • AWrong. 80 divides 5,280 feet by 66 inches without first changing the mile to inches.
    • BWrong. 480 uses 21 inches as the radius, which doubles the circumference to 132 inches. 21 inches is the diameter.
    • CCorrect. The circumference is 22/7 × 21 = 66 inches, a mile is 63,360 inches, and 63,360 ÷ 66 = 960.
    • DWrong. 3,017 divides 63,360 inches by the 21-inch diameter. The distance around the wheel is π times the diameter, 66 inches.

Word Knowledge: 15 questions

Choose the word or phrase closest in meaning to the underlined word. Real test: 15 questions in 9 minutes.

  1. Tidy most nearly means

    1. Aneat
    2. Bsmall
    3. Cmessy
    4. Dquick
    Show answer and explanation

    Answer: A. Something tidy is neat and in good order.

    • ACorrect. Tidy means neat: clean and well arranged.
    • BWrong. Small describes size. A tidy room can be any size.
    • CWrong. Messy is the opposite of tidy.
    • DWrong. Quick describes speed, not how orderly something is.
  2. Fragile most nearly means

    1. Acostly
    2. Bsturdy
    3. Cbreakable
    4. Dlightweight
    Show answer and explanation

    Answer: C. Something fragile breaks easily, like thin glass.

    • AWrong. Costly means expensive. Fragile items can be expensive, but fragile is about breaking.
    • BWrong. Sturdy means strong and hard to break, the opposite of fragile.
    • CCorrect. Fragile means easily broken, which is what breakable means.
    • DWrong. Lightweight means not heavy; a light object can still be strong.
  3. The rain forced the club to postpone the picnic until next Saturday.
    The underlined word most nearly means

    1. Adelay
    2. Bcancel
    3. Corganize
    4. Dshorten
    Show answer and explanation

    Answer: A. To postpone is to put off until a later time. The picnic still happens, just next Saturday.

    • ACorrect. Postpone means delay: move to a later time, as the picnic moves to next Saturday.
    • BWrong. To cancel is to call off for good. The sentence says the picnic will still happen next Saturday.
    • CWrong. To organize is to plan and arrange. The club had already planned the picnic.
    • DWrong. To shorten is to make shorter. The sentence is about when the picnic happens, not how long it lasts.
  4. Tranquil most nearly means

    1. Acalm
    2. Bnoisy
    3. Cremote
    4. Dsleepy
    Show answer and explanation

    Answer: A. Tranquil means calm and peaceful, free from noise or disturbance.

    • ACorrect. Tranquil means calm: quiet, peaceful, and undisturbed.
    • BWrong. Noisy is close to the opposite: a tranquil place is free of noise.
    • CWrong. Remote means far away. A quiet place is often remote, but tranquil describes the calm, not the distance.
    • DWrong. Sleepy means drowsy. A tranquilizer can make you sleepy, but tranquil itself means calm, not tired.
  5. The two witnesses gave contradictory accounts of the accident.
    The underlined word most nearly means

    1. Adetailed
    2. Bemotional
    3. Cidentical
    4. Dconflicting
    Show answer and explanation

    Answer: D. Contradictory accounts disagree with each other.

    • AWrong. Detailed means including many small facts; detailed accounts can still agree.
    • BWrong. Emotional means showing strong feelings.
    • CWrong. Identical means exactly the same, the opposite of contradictory.
    • DCorrect. Contradictory means conflicting: the accounts cannot both be true.
  6. Obsolete most nearly means

    1. Abroken
    2. Boutdated
    3. Cexpensive
    4. Dhidden
    Show answer and explanation

    Answer: B. Something obsolete is out of date and no longer used because something newer has replaced it.

    • AWrong. A broken item does not work. An obsolete item may still work but has been replaced by something newer.
    • BCorrect. Obsolete means outdated: no longer in use because something newer took its place.
    • CWrong. Expensive means costly. Obsolete items are often cheap because few people want them.
    • DWrong. Hidden means kept out of sight, which has nothing to do with being out of date.
  7. Hinder most nearly means

    1. Ahamper
    2. Bhurry
    3. Cassist
    4. Dhide
    Show answer and explanation

    Answer: A. To hinder is to get in the way of something: to hamper it.

    • ACorrect. Hinder means hamper: to slow down or get in the way of progress.
    • BWrong. Hurry means to move fast. Hindering something usually slows it down.
    • CWrong. Assist means to help, the opposite of hinder.
    • DWrong. Hide means to put out of sight. Hinder sounds a little like hide, but it means to obstruct.
  8. The treasurer made prudent choices to keep the club out of debt.
    The underlined word most nearly means

    1. Abold
    2. Bsensible
    3. Cgenerous
    4. Dhurried
    Show answer and explanation

    Answer: B. Prudent means careful and sensible, especially with money.

    • AWrong. Bold means daring or willing to take risks. Prudent choices avoid risk, which is how they keep the club out of debt.
    • BCorrect. Prudent means sensible and careful, which fits choices made to stay out of debt.
    • CWrong. Generous means giving freely. Generous spending would make debt more likely, not less.
    • DWrong. Hurried means done too fast. Prudent choices are made with care and thought.
  9. Meticulous most nearly means

    1. Asloppy
    2. Bnervous
    3. Cskilled
    4. Dthorough
    Show answer and explanation

    Answer: D. Meticulous means paying very close attention to every detail, which is what thorough means.

    • AWrong. Sloppy means careless and messy, the opposite of meticulous.
    • BWrong. Nervous means worried or uneasy.
    • CWrong. Skilled means having ability from training or practice. A skilled worker may or may not be careful with details.
    • DCorrect. Meticulous means extremely careful and thorough, with attention to every detail.
  10. Even after the long night shift, the nurse gave a lucid report on each patient.
    The underlined word most nearly means

    1. Alengthy
    2. Bclear
    3. Cnervous
    4. Dcareless
    Show answer and explanation

    Answer: B. Lucid means clear and easy to understand.

    • AWrong. Lengthy means long. A lucid report is easy to follow whatever its length.
    • BCorrect. Lucid means clear and easy to understand.
    • CWrong. Nervous means uneasy or worried. Lucid describes how understandable the report is, not the speaker's feelings.
    • DWrong. Careless means sloppy. The words "even after the long night shift" point to a report that stayed clear despite fatigue, not one that was sloppy.
  11. Benevolent most nearly means

    1. Awealthy
    2. Bkind
    3. Cstern
    4. Dclever
    Show answer and explanation

    Answer: B. Benevolent means well-meaning and kind toward others.

    • AWrong. Wealthy means rich. A benevolent person may give money away, but the word describes goodwill, not wealth.
    • BCorrect. Benevolent means kind and wishing others well.
    • CWrong. Stern means strict or harsh, close to the opposite of benevolent.
    • DWrong. Clever means smart or quick-witted. Benevolent describes a person's goodwill, not intelligence.
  12. The witness's story was plausible, so the detective took it seriously.
    The underlined word most nearly means

    1. Aconfusing
    2. Bdramatic
    3. Crehearsed
    4. Dbelievable
    Show answer and explanation

    Answer: D. Plausible means reasonable and likely to be true: believable.

    • AWrong. Confusing means hard to follow. A confusing story would give the detective less reason to take it seriously.
    • BWrong. Dramatic means exciting or full of emotion. A story can be dramatic without being likely to be true.
    • CWrong. Rehearsed means practiced ahead of time, which would make a detective more suspicious, not less.
    • DCorrect. Plausible means believable, which is why the detective took the story seriously.
  13. Laconic most nearly means

    1. Atalkative
    2. Bsluggish
    3. Cconcise
    4. Dgloomy
    Show answer and explanation

    Answer: C. A laconic person uses very few words.

    • AWrong. Talkative is the opposite: a laconic speaker says as little as possible.
    • BWrong. Sluggish means slow or lacking energy. Laconic sounds a little like lazy, but it describes speech, not energy.
    • CCorrect. Laconic means concise: using few words.
    • DWrong. Gloomy means sad or dark. A laconic person may be cheerful or gloomy; the word describes only how briefly they speak.
  14. Ubiquitous most nearly means

    1. Arare
    2. Bancient
    3. Charmful
    4. Dwidespread
    Show answer and explanation

    Answer: D. Ubiquitous means found everywhere: widespread.

    • AWrong. Rare means seldom found, the opposite of ubiquitous.
    • BWrong. Ancient means very old. Something ubiquitous can be brand new, like a popular phone app.
    • CWrong. Harmful means causing damage. Ubiquitous says only how common something is, not whether it is good or bad.
    • DCorrect. Ubiquitous means present everywhere, so widespread is the closest meaning.
  15. Critics called the senator's apology disingenuous, since the senator had defended the same remarks only a day earlier.
    The underlined word most nearly means

    1. Ainsincere
    2. Bnaive
    3. Cheartfelt
    4. Doverdue
    Show answer and explanation

    Answer: A. Disingenuous means not sincere or honest; pretending to feel something one does not.

    • ACorrect. Disingenuous means insincere. Defending the remarks a day earlier suggests the apology was not genuine.
    • BWrong. Naive means innocent or too trusting. That is a meaning of ingenuous; adding dis- turns it into the opposite idea of not being candid.
    • CWrong. Heartfelt means deeply sincere, the opposite of disingenuous.
    • DWrong. Overdue means late. The clue in the sentence is about the apology's honesty, not its timing.

Paragraph Comprehension: 10 questions

Read each short passage, then answer the question about it. Real test: 10 questions in 27 minutes.

  1. There are three safe ways to thaw frozen meat: in the refrigerator, in cold water, and in the microwave. The refrigerator method is slowest, taking about a day for every five pounds, but meat thawed this way may be refrozen without cooking it first. Meat thawed in cold water or in the microwave should be cooked right away. Thawing meat on the counter is unsafe, because the outside can get warm enough for bacteria to grow while the center is still frozen.

    According to the passage, thawing meat on the counter is unsafe because

    1. Athe meat then has to be cooked right away.
    2. Bthe meat can never be refrozen after it thaws.
    3. Cthe surface can warm while the middle stays frozen.
    4. Dit takes about one day for every five pounds of meat.
    Show answer and explanation

    Answer: C. The last sentence explains the danger: the outer layer warms enough for bacteria while the center stays frozen. The key restates that as the surface warming while the middle stays frozen.

    • AWrong. Cooking right away is advice for meat thawed in cold water or the microwave, not the reason counter thawing is unsafe.
    • BWrong. Refreezing is discussed only for the refrigerator method. It is not the reason given for avoiding the counter.
    • CCorrect. The passage says the outside can get warm enough for bacteria to grow while the center is still frozen.
    • DWrong. This timing describes the refrigerator method, not thawing on the counter.
  2. The forecast called for clear skies, so the two hikers set out early for the summit. By noon, dark clouds were piling up over the ridge, and a cold wind had begun to blow. They were only a mile from the top, but after studying the sky, they turned around and started back down. Thunder rumbled just as they reached the parking lot.

    Which statement best summarizes what happens in the passage?

    1. AThe hikers made it to the top.
    2. BThe forecast warned of a storm.
    3. CThe hikers got lost on the way down.
    4. DA coming storm made the hikers turn back.
    Show answer and explanation

    Answer: D. The story turns on one decision: seeing the weather change, the hikers turned back a mile short of the top. The key sums up that decision and its cause.

    • AWrong. The hikers turned around a mile from the top, so they never reached the summit.
    • BWrong. This reverses the passage. The forecast called for clear skies.
    • CWrong. Nothing suggests the hikers lost their way. They reached the parking lot.
    • DCorrect. The hikers were close to the top, saw the storm building, and turned back, reaching the parking lot as thunder began.
  3. The Main Street entrance to the public library will be closed for repairs for the next two weeks. During the first week, visitors should use the side door on Park Avenue, which will be open during regular library hours.

    During the second week, workers will be rebuilding the Park Avenue steps, so the side door will open only after 3:00 p.m. Before 3:00 p.m. that week, visitors should enter through the community room door at the back of the building. Staff will be posted at each open door to answer questions.

    According to the notice, how should a visitor enter the library at 10:00 a.m. during the second week of repairs?

    1. AThrough the community room door at the back
    2. BThrough the side door on Park Avenue
    3. CThrough the Main Street entrance
    4. DThrough the staff door by the loading dock
    Show answer and explanation

    Answer: A. In the second week, the Park Avenue side door opens only after 3:00 p.m. Before then, visitors use the community room door at the back of the building.

    • ACorrect. 10:00 a.m. is before 3:00 p.m., and in the second week the notice sends visitors to the community room door at the back before that time.
    • BWrong. The side door is the entrance for the first week. In the second week it opens only after 3:00 p.m. because the steps are being rebuilt.
    • CWrong. The Main Street entrance is closed for the full two weeks of repairs.
    • DWrong. The notice never mentions a staff door or a loading dock. Staff are posted at the open doors only to answer questions.
  4. Chocolate is a favorite treat for many people, but it can make dogs seriously ill. It contains theobromine, a substance that dogs break down much more slowly than people do. A small amount can cause vomiting and a racing heart, and a larger amount can cause seizures. Dark chocolate and baking chocolate are the most dangerous kinds because they contain the most theobromine. If your dog eats chocolate, call your veterinarian or an animal poison control center right away.

    The author's main purpose in the passage is to

    1. Aexplain why people enjoy eating chocolate.
    2. Bcompare dark chocolate with milk chocolate.
    3. Cdescribe how veterinarians treat sick dogs.
    4. Dwarn dog owners that chocolate can harm pets.
    Show answer and explanation

    Answer: D. The passage explains why chocolate is dangerous to dogs, lists the signs of poisoning, and tells owners to call for help, so its purpose is to warn.

    • AWrong. The passage mentions that people like chocolate only to set up its real point, which is the danger to dogs.
    • BWrong. Dark and baking chocolate come up only to show which kinds are most dangerous. The passage never compares them with milk chocolate.
    • CWrong. The passage tells owners to call a veterinarian but never describes any treatment.
    • DCorrect. Every sentence points to the danger chocolate poses to dogs, ending with what to do if a dog eats it.
  5. The Pony Express began carrying mail between Missouri and California in April 1860. Riders switched to fresh horses at stations spaced about ten to fifteen miles apart and could carry a letter the length of the route in about ten days, far faster than a stagecoach. In October 1861, the first telegraph line across the continent was completed, allowing messages to cross the country in minutes. Just two days later, the Pony Express announced that it would stop operating.

    The passage suggests that the Pony Express ended mainly because

    1. Aa quicker way to send messages had arrived.
    2. Briders could not find enough fresh horses.
    3. Cits stations were too far apart.
    4. Dstagecoaches had become faster.
    Show answer and explanation

    Answer: A. The timing gives the clue: the service shut down two days after the telegraph began sending messages across the country in minutes. That points to the faster telegraph as the reason.

    • ACorrect. The Pony Express announced its end just two days after the telegraph, which sent messages in minutes instead of days, was completed.
    • BWrong. The passage says riders did switch to fresh horses at stations. Nothing suggests a shortage.
    • CWrong. The spacing of the stations is given as a fact, not as a problem, and the passage calls the service fast.
    • DWrong. The passage says the Pony Express was far faster than a stagecoach, so this reverses it.
  6. Honeybees do not hibernate in winter. When the air turns cold, the workers form a tight ball, called a cluster, around their queen. Bees in the center shiver their flight muscles without moving their wings, which produces heat. Bees on the outside of the cluster pack closely together, head inward, forming a living blanket that holds that heat in.

    The colder the weather, the tighter the cluster draws together. On milder days it loosens, and some bees fly out briefly before returning. All winter the colony lives on honey stored during the warmer months, and the cluster creeps slowly across the comb so that it stays in contact with its food.

    According to the passage, the bees on the outside of the cluster mainly

    1. Aproduce heat by shivering their flight muscles
    2. Bfly out of the hive on mild days to gather food
    3. Ckeep the heat from escaping the cluster
    4. Dmove the stored honey closer to the queen
    Show answer and explanation

    Answer: C. The passage says the outer bees pack closely together and form a living blanket that holds in the heat made by the bees in the center.

    • AWrong. Shivering to make heat is the job the passage gives to the bees in the center of the cluster.
    • BWrong. The passage says some bees fly out briefly on mild days and then return. It does not say they gather food, and it does not tie this to the outer bees.
    • CCorrect. The outer bees form "a living blanket that holds that heat in," so their main role is insulation.
    • DWrong. The bees do not move the honey. The whole cluster moves across the comb to stay near its food.
  7. On a hot summer day, a long steel bridge can be several inches longer than it is on a cold winter night, because steel expands as it warms and shrinks as it cools. If the ends of the bridge were fixed solidly in place, this constant stretching and shrinking would push and pull on the structure until parts of it cracked or buckled.

    To prevent this, engineers build expansion joints into bridges. These are gaps, often spanned by interlocking metal teeth, that let sections of the deck slide slightly as their length changes. The steady thump drivers hear when crossing some bridges comes from rolling over these joints.

    Which statement best expresses the main idea of the passage?

    1. AExpansion joints let a bridge change length safely as the temperature changes.
    2. BSteel bridges are several inches longer in summer than they are in winter.
    3. CThe thumping sound on a bridge warns drivers that a joint has come loose.
    4. DEngineers avoid using steel in bridges because it expands when it warms.
    Show answer and explanation

    Answer: A. The passage explains the problem (steel grows and shrinks with temperature) and the solution it is built around: expansion joints that let the deck move without cracking.

    • ACorrect. The passage describes why bridges change length and how expansion joints let them do so without cracking or buckling, which covers both paragraphs.
    • BWrong. The passage does say this, but it is the cause that sets up the main point about expansion joints, not the main idea itself.
    • CWrong. The passage says the thump comes from rolling over the joints during normal use. It never says the sound means a joint is loose.
    • DWrong. The passage describes steel bridges and how engineers handle expansion. It never says engineers avoid steel.
  8. The Great Basin Desert is a cold desert: it gets little rain, and much of its yearly moisture falls as winter snow. Plant cover there is sparse. Sagebrush and other shrubs grow several feet apart, with bare ground showing between them.

    Scientists think this spacing comes partly from competition for water. Each shrub's roots spread widely through the soil around it, drawing moisture from a large area, so too little is left for another plant to take hold close by.

    In the passage, the word sparse most nearly means

    1. Adry.
    2. Bwoody.
    3. Cscattered.
    4. Dlow-growing.
    Show answer and explanation

    Answer: C. The next sentence explains the word: the shrubs grow several feet apart with bare ground between them, so the plant cover is thinly scattered.

    • AWrong. The desert itself is dry, but the sentence describes how much ground the plants cover, and the next sentence says they grow far apart.
    • BWrong. Sagebrush is a woody shrub, but sparse describes how the plants are spread out, not what they are made of.
    • CCorrect. The shrubs grow several feet apart with bare ground between them, so sparse means thinly scattered.
    • DWrong. The passage calls the shrubs neither tall nor short. Sparse is explained by the spacing between plants, not by their height.
  9. Full-time employees who have completed six months of service may apply for tuition assistance. The company will pay 75 percent of tuition, up to $2,000 per calendar year, for courses related to the employee's current job or to a position the employee could reasonably move into. Books and fees are not covered.

    To be paid, the employee must submit a course approval form before the course begins and must report a final grade of C or better within 30 days after the course ends. Employees who leave the company within one year of receiving assistance must repay the full amount.

    Each employee below takes a job-related course and reports the final grade within 30 days. According to the policy, which one qualifies for tuition assistance?

    1. AA part-time worker with two years of service who files the form before class and earns an A
    2. BA full-time worker with four months of service who files the form before class and earns a B
    3. CA full-time worker with one year of service who files the form during the course and earns an A
    4. DA full-time worker with eight months of service who files the form before class and earns a C
    Show answer and explanation

    Answer: D. The policy requires full-time status, at least six months of service, an approval form filed before the course begins, and a grade of C or better. Only the eight-month full-time worker who filed before class and earned a C meets every condition.

    • AWrong. The policy covers full-time employees only, so a part-time worker does not qualify, however long the service or high the grade.
    • BWrong. The policy requires six months of service before applying. Four months is not enough.
    • CWrong. The approval form must be submitted before the course begins. Filing it during the course breaks that rule, even with an A.
    • DCorrect. This worker is full-time, has more than six months of service, filed before class, and earned a C, which the policy accepts as "C or better."
  10. Planting a tree along a city street costs money, and so does caring for it. Young trees must be watered through their first few summers, and older trees need pruning so their branches stay clear of power lines and passing trucks. Roots can also lift sidewalk slabs, which then have to be repaired.

    Even so, many cities keep planting. A row of grown trees shades pavement that would otherwise soak up heat all afternoon, which keeps the street cooler for people walking by. Leaves and branches catch falling rain and slow it down, so less water rushes into storm drains during a heavy shower. Many residents also say that a tree-lined block simply feels like a better place to live.

    Which statement best expresses the main idea of the passage?

    1. AStreet trees need more care than most city residents realize.
    2. BStreet trees cost money to keep, but cities find them worth it.
    3. CTree roots damage sidewalks, so cities should plant smaller trees.
    4. DShade from trees is the main way cities keep their streets cool.
    Show answer and explanation

    Answer: B. The first paragraph lays out what street trees cost, and the second explains why cities plant them anyway. The main idea joins the two: the costs are real, but the benefits keep cities planting.

    • AWrong. The passage lists the care trees need, but it never says residents are unaware of it, and it ignores the second paragraph on benefits.
    • BCorrect. The first paragraph covers the costs and the second explains why cities keep planting anyway, so this statement covers the whole passage.
    • CWrong. The passage mentions roots lifting sidewalks as one cost, but it never suggests planting smaller trees.
    • DWrong. Shade is one benefit the passage names, but it never says trees are the main way cities cool streets, and it leaves out the costs.

Mathematics Knowledge: 15 questions

High school math: number properties, algebra, geometry. No calculator. Real test: 15 questions in 31 minutes.

  1. A box is 5 inches long, 4 inches wide, and 3 inches high. What is its volume in cubic inches?

    1. A12
    2. B20
    3. C60
    4. D94
    Show answer and explanation

    Answer: C. Volume = length × width × height = 5 × 4 × 3 = 60 cubic inches.

    • AWrong. 12 adds the three dimensions (5 + 4 + 3) instead of multiplying them.
    • BWrong. 20 is the area of the bottom (5 × 4). It still has to be multiplied by the height of 3.
    • CCorrect. 5 × 4 × 3 = 60 cubic inches.
    • DWrong. 94 is the surface area, 2 × (20 + 15 + 12), which measures the outside of the box, not the space inside.
  2. A gym charges a $40 sign-up fee plus $25 per month. Which expression gives the total cost, in dollars, for m months?

    1. A40 + 25m
    2. B25 + 40m
    3. C65m
    4. D40 + m
    Show answer and explanation

    Answer: A. The $40 fee is paid once, and $25 is paid for each of the m months: 40 + 25m.

    • ACorrect. The one-time fee is 40, and 25 is charged every month, so the total is 40 + 25m.
    • BWrong. 25 + 40m swaps the numbers, charging $40 every month and $25 once.
    • CWrong. 65m charges the sign-up fee again every month.
    • DWrong. 40 + m adds the number of months instead of charging $25 for each one.
  3. Solve for x: 0.4x + 1.2 = 3.6

    1. A0.6
    2. B6
    3. C7.8
    4. D12
    Show answer and explanation

    Answer: B. Subtract 1.2 from both sides: 0.4x = 2.4. Divide by 0.4: x = 6.

    • AWrong. 0.6 divides 2.4 by 4 instead of by 0.4.
    • BCorrect. 0.4x = 3.6 − 1.2 = 2.4, and 2.4 ÷ 0.4 = 6.
    • CWrong. 7.8 divides 3.6 by 0.4 first (9) and then subtracts 1.2, which undoes the steps in the wrong order.
    • DWrong. 12 adds 1.2 to 3.6 instead of subtracting it: 4.8 ÷ 0.4 = 12.
  4. (x + 4)(x − 3) =

    1. Ax² − 12
    2. Bx² − x − 12
    3. Cx² + x − 12
    4. Dx² + 7x − 12
    Show answer and explanation

    Answer: C. FOIL: x·x + x·(−3) + 4·x + 4·(−3) = x² − 3x + 4x − 12 = x² + x − 12.

    • AWrong. x² − 12 multiplies only the first terms and the last terms and drops the middle terms −3x and 4x.
    • BWrong. x² − x − 12 gets the middle term's sign wrong: −3x + 4x is +x, not −x.
    • CCorrect. x² − 3x + 4x − 12 simplifies to x² + x − 12.
    • DWrong. x² + 7x − 12 adds 4 and 3 for the middle term, ignoring the minus sign on the 3.
  5. What is the midpoint of the segment joining (2, 5) and (8, 1)?

    1. A(3, 2)
    2. B(5, 3)
    3. C(6, −4)
    4. D(10, 6)
    Show answer and explanation

    Answer: B. Average the coordinates: ((2 + 8) ÷ 2, (5 + 1) ÷ 2) = (5, 3).

    • AWrong. (3, 2) halves the differences, (8 − 2) ÷ 2 and (5 − 1) ÷ 2, instead of averaging the coordinates.
    • BCorrect. (2 + 8) ÷ 2 = 5 and (5 + 1) ÷ 2 = 3, so the midpoint is (5, 3).
    • CWrong. (6, −4) subtracts the coordinates, 8 − 2 and 1 − 5, which gives how far apart the points are, not the middle.
    • DWrong. (10, 6) adds the coordinates but forgets to divide by 2.
  6. √50 =

    1. A2√5
    2. B5√2
    3. C5√10
    4. D25√2
    Show answer and explanation

    Answer: B. √50 = √(25 × 2) = √25 × √2 = 5√2.

    • AWrong. 2√5 swaps the numbers; 2√5 = √20.
    • BCorrect. 50 = 25 × 2 and √25 = 5, so √50 = 5√2.
    • CWrong. 5√10 splits 50 as 5 × 10 and pulls out the 5 as if it were 5²; 5√10 = √250.
    • DWrong. 25√2 pulls the 25 out without taking its square root; 25√2 = √1250.
  7. The trapezoid shown has parallel bases of 6 and 10 and a height of 4. What is its area?

    6104
    1. A24
    2. B32
    3. C40
    4. D64
    Show answer and explanation

    Answer: B. Area = ½ × (base₁ + base₂) × height = ½ × (6 + 10) × 4 = 32.

    • AWrong. 24 uses only the short base (6 × 4).
    • BCorrect. ½ × (6 + 10) × 4 = ½ × 16 × 4 = 32.
    • CWrong. 40 uses only the long base (10 × 4).
    • DWrong. 64 adds the bases and multiplies by the height but forgets the ½.
  8. Solve for x: 4(x − 2) = 2x + 10

    1. A1
    2. B3
    3. C6
    4. D9
    Show answer and explanation

    Answer: D. Distribute: 4x − 8 = 2x + 10. Subtract 2x and add 8 to both sides: 2x = 18, so x = 9.

    • AWrong. 1 moves the −8 to the right side without changing its sign: 2x = 10 − 8 = 2.
    • BWrong. 3 adds 2x to the left side instead of subtracting it: 6x − 8 = 10, so 6x = 18.
    • CWrong. 6 forgets to distribute the 4 to the −2: 4x − 2 = 2x + 10, so 2x = 12.
    • DCorrect. 4x − 8 = 2x + 10, so 2x = 18 and x = 9.
  9. 2 1/2 × 1 3/5 =

    1. A1 9/16
    2. B2 3/10
    3. C3 7/10
    4. D4
    Show answer and explanation

    Answer: D. Change to improper fractions: 5/2 × 8/5 = 40/10 = 4.

    • AWrong. 1 9/16 flips the second fraction (5/2 × 5/8), which is division, not multiplication.
    • BWrong. 2 3/10 multiplies the whole numbers (2 × 1) and the fractions (1/2 × 3/5) separately. Mixed numbers must be changed to improper fractions first.
    • CWrong. 3 7/10 multiplies only the 2 by 1 3/5 (getting 3 1/5) and then adds the 1/2 instead of multiplying it too.
    • DCorrect. 5/2 × 8/5 = 40/10 = 4.
  10. 5 1/4 − 2 2/3 =

    1. A2 5/12
    2. B2 7/12
    3. C3 5/12
    4. D3 7/12
    Show answer and explanation

    Answer: B. Use twelfths: 5 3/12 − 2 8/12. Regroup: 4 15/12 − 2 8/12 = 2 7/12.

    • AWrong. 2 5/12 regroups 1 as 10/12 instead of 12/12: 4 13/12 − 2 8/12.
    • BCorrect. Rename as 4 15/12 − 2 8/12, which equals 2 7/12.
    • CWrong. 3 5/12 subtracts the smaller fraction from the larger one (2/3 − 1/4 = 5/12) instead of regrouping.
    • DWrong. 3 7/12 regroups to get 15/12 but forgets to lower the 5 to 4.
  11. What is the prime factorization of 252?

    1. A2² × 3 × 7
    2. B2 × 3² × 7
    3. C2² × 3² × 7
    4. D2³ × 3² × 7
    Show answer and explanation

    Answer: C. 252 = 2 × 126 = 2 × 2 × 63 = 2 × 2 × 3 × 21 = 2 × 2 × 3 × 3 × 7, which is 2² × 3² × 7.

    • AWrong. 2² × 3 × 7 = 84. It is missing one factor of 3.
    • BWrong. 2 × 3² × 7 = 126. It is missing one factor of 2.
    • CCorrect. 252 = 2 × 2 × 3 × 3 × 7 = 2² × 3² × 7.
    • DWrong. 2³ × 3² × 7 = 504, twice 252. It has one factor of 2 too many.
  12. What is the measure of each interior angle of a regular hexagon?

    1. A60°
    2. B108°
    3. C120°
    4. D720°
    Show answer and explanation

    Answer: C. The interior angles of a hexagon add up to (6 − 2) × 180° = 720°. A regular hexagon has 6 equal angles, so each is 720° ÷ 6 = 120°.

    • AWrong. 60° is 360° ÷ 6, the exterior angle (or the angle at the center), not the interior angle.
    • BWrong. 108° is each interior angle of a regular pentagon, which has 5 sides, not 6.
    • CCorrect. (6 − 2) × 180° = 720°, and 720° ÷ 6 = 120°.
    • DWrong. 720° is the sum of all six interior angles. It still has to be divided by 6.
  13. A bag holds 4 red, 5 blue, and 3 green marbles. One marble is drawn at random. What is the probability that it is NOT blue?

    1. A1/4
    2. B5/12
    3. C7/12
    4. D5/7
    Show answer and explanation

    Answer: C. There are 4 + 5 + 3 = 12 marbles, and 4 + 3 = 7 are not blue, so the probability is 7/12.

    • AWrong. 1/4 is 3/12, the probability of green only. Red marbles are not blue either.
    • BWrong. 5/12 is the probability that the marble IS blue.
    • CCorrect. 7 of the 12 marbles are not blue, so the probability is 7/12.
    • DWrong. 5/7 compares blue marbles to non-blue marbles. A probability compares the wanted outcomes to all 12 marbles.
  14. If x + y = 10 and x − y = 4, what is the value of y?

    1. A3
    2. B6
    3. C7
    4. D14
    Show answer and explanation

    Answer: A. Subtract the second equation from the first: 2y = 6, so y = 3. (Then x = 7.)

    • ACorrect. Subtracting the equations gives 2y = 6, so y = 3.
    • BWrong. 6 is the value of 2y; it still has to be divided by 2.
    • CWrong. 7 is the value of x, not y.
    • DWrong. 14 is 2x, from adding the equations; it is neither x nor y.
  15. Which inequality is the solution of −3 < 2x + 1 ≤ 9?

    1. A−4 < x ≤ 8
    2. B−1 < x ≤ 5
    3. C−2 < x ≤ 4
    4. D−2 ≤ x < 4
    Show answer and explanation

    Answer: C. Subtract 1 from all three parts: −4 < 2x ≤ 8. Divide all three parts by 2: −2 < x ≤ 4.

    • AWrong. −4 < x ≤ 8 subtracts 1 but forgets to divide every part by 2.
    • BWrong. −1 < x ≤ 5 adds 1 to each part instead of subtracting it: −2 < 2x ≤ 10.
    • CCorrect. Subtracting 1 from every part gives −4 < 2x ≤ 8, and dividing by 2 gives −2 < x ≤ 4.
    • DWrong. The numbers are right, but the inequality signs are swapped. Dividing by a positive number keeps < on the left and ≤ on the right.

Electronics Information: 15 questions

Electricity, circuits, and electronic components. Real test: 15 questions in 10 minutes.

  1. Electrical power is measured in which unit?

    1. AAmpere
    2. BOhm
    3. CVolt
    4. DWatt
    Show answer and explanation

    Answer: D. The watt is the unit of power, the rate at which electrical energy is used. Power in watts equals volts × amperes.

    • AWrong. The ampere measures current, the rate at which charge flows.
    • BWrong. The ohm measures resistance, how much a material opposes current.
    • CWrong. The volt measures voltage, the electrical push that drives current.
    • DCorrect. The watt measures power, and watts = volts × amperes.
  2. To measure the voltage across a lamp in a working circuit, how should the voltmeter be connected?

    1. AIn series with the lamp
    2. BIn series with the switch
    3. CIn parallel with the lamp
    4. DIn parallel with the fuse
    Show answer and explanation

    Answer: C. A voltmeter measures the difference in voltage between two points, so its leads go on both sides of the lamp, in parallel with it.

    • AWrong. A voltmeter has a very high resistance, so in series it blocks almost all the current and reads close to the full supply voltage instead of the lamp voltage.
    • BWrong. In series with the switch, the meter sits in the single current path; its high resistance stops the lamp from lighting, so the reading is not the lamp voltage.
    • CCorrect. Placing the leads on both sides of the lamp, in parallel, reads the voltage drop across the lamp.
    • DWrong. Across a good fuse the meter reads nearly zero, because a fuse has almost no voltage drop.
  3. Before using an ohmmeter to measure the resistance of a part in a circuit, what should be done first?

    1. ALeave the power on so current flows through the part
    2. BConnect the meter in series with the load
    3. CTurn off the power to the circuit
    4. DSet the meter to read AC volts
    Show answer and explanation

    Answer: C. An ohmmeter sends its own small current from its battery through the part. Outside voltage in the circuit gives false readings and can damage the meter, so the power must be off.

    • AWrong. With power on, the circuit's voltage adds to the meter's own test current, giving false readings and risking damage to the meter.
    • BWrong. Series connection is how an ammeter is used; an ohmmeter's leads go across the part with the power off.
    • CCorrect. An ohmmeter supplies its own test current, so the circuit must be unpowered for a correct and safe reading.
    • DWrong. The AC volts setting measures voltage, not resistance; the meter must be set to ohms.
  4. Which of these is a source of direct current (DC)?

    1. AA car battery
    2. BA wall outlet in a home
    3. CThe power company's street lines
    4. DA step-down transformer
    Show answer and explanation

    Answer: A. A battery pushes current in one direction only, from one terminal around the circuit to the other, which is direct current.

    • ACorrect. A battery's chemical reaction keeps one terminal positive and the other negative, so current flows one way: direct current.
    • BWrong. A US household outlet supplies alternating current that reverses direction 60 times a second.
    • CWrong. Power company lines carry alternating current, because AC voltage can be raised and lowered with transformers.
    • DWrong. A transformer works only with alternating current, and its output is also alternating current.
  5. A coil of wire wound around a movable iron plunger pulls the plunger into the coil when current flows. This device is a

    1. Acapacitor.
    2. Brheostat.
    3. Csolenoid.
    4. Dtransformer.
    Show answer and explanation

    Answer: C. A solenoid is a coil that becomes an electromagnet when current flows, pulling its iron plunger in to push or pull a mechanism, such as a door lock or a starter's engagement lever.

    • AWrong. A capacitor stores charge on plates separated by an insulator; it has no coil or moving plunger.
    • BWrong. A rheostat is a variable resistor used to adjust current; it does not move a plunger.
    • CCorrect. Current through the coil makes a magnetic field that pulls the iron plunger in, which is how a solenoid turns electricity into straight-line motion.
    • DWrong. A transformer uses two coils on a fixed iron core to change AC voltage; nothing in it moves.
  6. In the circuit shown, what is the equivalent resistance of R1 and R2?

    +12 VR1 = 6 ΩR2 = 12 Ω
    1. A0.25 Ω
    2. B4 Ω
    3. C9 Ω
    4. D18 Ω
    Show answer and explanation

    Answer: B. For parallel resistors, R = (6 × 12) ÷ (6 + 12) = 72 ÷ 18 = 4 Ω.

    • AWrong. 0.25 is 1/6 + 1/12, the value of 1/R; it still has to be inverted.
    • BCorrect. R = (6 × 12) ÷ (6 + 12) = 4 Ω, less than the smaller resistor as it must be.
    • CWrong. 9 Ω is the average of 6 and 12, which is not how parallel resistors combine.
    • DWrong. 18 Ω adds the resistors, which is the rule for series, not parallel.
  7. A circuit draws 3 A. If the voltage is cut in half and the resistance is doubled, what current will flow?

    1. A0.75 A
    2. B1.5 A
    3. C3 A
    4. D6 A
    Show answer and explanation

    Answer: A. I = V ÷ R. Halving V cuts the current in half, and doubling R cuts it in half again: 3 × 1/2 × 1/2 = 0.75 A.

    • ACorrect. Each change halves the current, so 3 A becomes 1.5 A and then 0.75 A.
    • BWrong. 1.5 A accounts for only one of the two changes; both the lower voltage and the higher resistance reduce current.
    • CWrong. 3 A assumes the two changes cancel, but both of them reduce the current.
    • DWrong. 6 A treats the changes as increasing current; less voltage and more resistance both lower it.
  8. A thermistor is a resistor whose resistance changes mainly with changes in

    1. Alight level.
    2. Btemperature.
    3. Capplied voltage.
    4. Dmagnetic field strength.
    Show answer and explanation

    Answer: B. A thermistor (thermal resistor) is made so its resistance changes sharply with temperature, which is why it is used in thermostats and temperature sensors.

    • AWrong. A resistor that changes with light is a photoresistor (light-dependent resistor).
    • BCorrect. A thermistor's resistance changes sharply with temperature, so it is used to sense heat.
    • CWrong. A resistor that changes sharply with voltage is a varistor, used for surge protection.
    • DWrong. Resistance that changes with a magnetic field describes a magnetoresistor, not a thermistor.
  9. A 12-volt battery is rated at 50 ampere-hours. Ideally, how long can it supply a steady current of 2.5 A?

    1. A4.2 hours
    2. B20 hours
    3. C125 hours
    4. D600 hours
    Show answer and explanation

    Answer: B. Ampere-hours ÷ amperes = hours: 50 ÷ 2.5 = 20 hours. The voltage does not enter this calculation.

    • AWrong. 4.2 hours divides the ampere-hours by the voltage (50 ÷ 12); the current, not the voltage, sets the time.
    • BCorrect. 50 ampere-hours ÷ 2.5 A = 20 hours.
    • CWrong. 125 hours multiplies the rating by the current (50 × 2.5) instead of dividing.
    • DWrong. 600 hours multiplies the rating by the voltage (50 × 12), which gives watt-hours, not hours.
  10. Resistors of 10 Ω, 20 Ω, and 30 Ω are connected in series across a 12-volt battery. How much current flows in the circuit?

    1. A0.2 A
    2. B0.4 A
    3. C1.2 A
    4. D2.2 A
    Show answer and explanation

    Answer: A. In series the resistances add: 10 + 20 + 30 = 60 Ω. By Ohm's law, I = V ÷ R = 12 ÷ 60 = 0.2 A.

    • ACorrect. Series resistances add to 60 Ω, and 12 V ÷ 60 Ω = 0.2 A.
    • BWrong. 0.4 A uses only the 30-Ω resistor; in series the current must pass through all three, so their resistances add.
    • CWrong. 1.2 A uses only the 10-Ω resistor; the other two resistors are in the same path and also limit the current.
    • DWrong. 2.2 A adds 12/10 + 12/20 + 12/30, which is how branch currents add in a parallel circuit, not a series one.
  11. Which component is a resistor whose value is changed by turning a shaft that moves a sliding contact along it, as in many volume knobs?

    1. AVaristor
    2. BPotentiometer
    3. CSolenoid
    4. DTransistor
    Show answer and explanation

    Answer: B. A potentiometer has a sliding contact (wiper) that moves along a resistive track when the shaft turns, so the resistance between its terminals changes.

    • AWrong. A varistor's resistance changes with the voltage across it, which makes it useful for surge protection; it has no knob or sliding contact.
    • BCorrect. A potentiometer's shaft moves a wiper along a resistive track, changing the resistance, which is why it is used in volume controls.
    • CWrong. A solenoid is a coil that pulls an iron core when current flows; it is an electromagnet, not an adjustable resistor.
    • DWrong. A transistor is a semiconductor device that switches or amplifies signals; it has no shaft or sliding contact.
  12. The current through a resistor doubles while its resistance stays the same. How does the power the resistor turns into heat change?

    1. AIt is halved
    2. BIt stays the same
    3. CIt doubles
    4. DIt quadruples
    Show answer and explanation

    Answer: D. Power in a resistor is P = I²R. With R fixed, doubling I multiplies the power by 2² = 4.

    • AWrong. Power falls only when current or resistance falls; here the current went up.
    • BWrong. Power depends on current, so a change in current always changes the power in a fixed resistor.
    • CWrong. Doubling is the trap of treating power as directly proportional to current; power goes with the square of current.
    • DCorrect. P = I²R, so with the same resistance, twice the current gives 2² = 4 times the power.
  13. A current flows in a coil of wire only while a magnet is moving into or out of the coil. Why?

    1. AThe moving magnet carries electrons into the wire
    2. BA changing magnetic field induces a voltage in the coil
    3. CFriction from the moving magnet builds up static charge
    4. DA magnet has a magnetic field only while it moves
    Show answer and explanation

    Answer: B. This is electromagnetic induction: a voltage is induced only while the magnetic field through the coil is changing.

    • AWrong. A magnet does not add electrons to the wire; it pushes the electrons already in the wire.
    • BCorrect. Only a changing magnetic field induces a voltage, so current flows while the magnet moves and stops when it is still.
    • CWrong. The effect needs no contact or friction; it is magnetic, not static electricity.
    • DWrong. A still magnet keeps its field; the field just is not changing, so nothing is induced.
  14. Two lamps are wired in parallel across a battery. A third lamp is added in parallel with them. What happens to the circuit's total resistance and to the total current drawn from the battery?

    1. ABoth stay the same
    2. BBoth increase
    3. CResistance increases and current decreases
    4. DResistance decreases and current increases
    Show answer and explanation

    Answer: D. Each parallel branch gives the current one more path, so the combined resistance drops. With the same battery voltage across a lower resistance, the total current rises.

    • AWrong. The new lamp draws its own current from the battery, so the total current cannot stay the same.
    • BWrong. Total resistance and total current cannot both rise with the same battery voltage; by Ohm's law one goes up only as the other goes down.
    • CWrong. Adding a lamp in series would raise the resistance and cut the current; adding one in parallel does the opposite.
    • DCorrect. An extra parallel path lowers the combined resistance, so the battery supplies more total current.
  15. In a simple power supply, a Zener diode is used mainly to:

    1. AChange DC into AC
    2. BStep the AC voltage up
    3. CStore energy between pulses
    4. DHold the output voltage steady
    Show answer and explanation

    Answer: D. Connected in reverse, a Zener diode conducts at a set breakdown voltage, holding the voltage across it nearly constant. It works as a voltage regulator.

    • AWrong. Changing DC into AC is the job of an inverter.
    • BWrong. Stepping AC voltage up or down is the job of a transformer.
    • CWrong. Storing energy between pulses to smooth the output is the job of a filter capacitor.
    • DCorrect. A reverse-connected Zener conducts at a fixed breakdown voltage, which regulates the output.

Auto Information: 10 questions

How cars work: engine, fuel, electrical, brakes, drivetrain. Real test: 10 questions in 7 minutes.

  1. What is the job of an engine's air filter?

    1. AClean the engine oil as it circulates
    2. BTrap dirt in the air going into the engine
    3. CRemove harmful gases from the exhaust
    4. DCool the air before it enters the cylinders
    Show answer and explanation

    Answer: B. The air filter catches dust and dirt before the intake air reaches the cylinders, where grit would wear the pistons, rings and cylinder walls.

    • AWrong. Cleaning the oil is the job of the oil filter, not the air filter.
    • BCorrect. The air filter traps dust and grit in the incoming air so it cannot wear the inside of the engine.
    • CWrong. Exhaust gases are cleaned by the catalytic converter, which is in the exhaust system.
    • DWrong. Intake air is cooled by an intercooler on turbocharged engines; the air filter only cleans the air.
  2. The part shown is a

    1. AGlow plug
    2. BFuel injector
    3. COxygen sensor
    4. DSpark plug
    Show answer and explanation

    Answer: D. The ribbed insulator, hex, threaded shell, and hooked ground electrode over the center electrode mark a spark plug. It fires the air-fuel mixture in a gasoline engine.

    • AWrong. A glow plug is a thin heating rod that helps start a cold diesel; it has no hooked ground electrode or spark gap.
    • BWrong. A fuel injector is an electric valve with a wiring connector and a spray nozzle; it has no electrodes.
    • CWrong. An oxygen sensor threads into the exhaust pipe and has a slotted metal shield over its tip, not a hooked electrode.
    • DCorrect. The hooked ground electrode just past the center electrode forms the spark gap, which marks this part as a spark plug.
  3. In the rear-wheel-drive layout shown, which number points to a universal joint?

    Engine1234
    1. A1
    2. B2
    3. C3
    4. D4
    Show answer and explanation

    Answer: B. A universal joint (2) is the flexible coupling at each end of the driveshaft. It lets the shaft keep turning at an angle as the rear axle moves up and down.

    • AWrong. 1 is the transmission, bolted to the back of the engine.
    • BCorrect. 2 is a universal joint, the flexible coupling at the end of the driveshaft.
    • CWrong. 3 is the driveshaft, the long tube that carries power back to the rear axle.
    • DWrong. 4 is the differential, which splits power between the two rear wheels.
  4. What is the main job of a car’s ABS during a hard stop?

    1. AApplies the parking brake as well
    2. BAdds brake fluid if the level is low
    3. CCools the brakes to prevent fade
    4. DKeeps the wheels from locking up
    Show answer and explanation

    Answer: D. ABS senses when a wheel is about to lock and rapidly releases and reapplies that brake. The tires keep rolling, so the driver can still steer.

    • AWrong. ABS works only on the service brakes through the hydraulic system; it does not use the parking brake.
    • BWrong. ABS does not add fluid; low brake fluid points to a leak or worn pads.
    • CWrong. ABS does not cool anything; it only controls the brake pressure at each wheel.
    • DCorrect. ABS rapidly releases and reapplies the brakes so the wheels keep turning and the driver can steer.
  5. A repair manual says the cylinder head bolts must be tightened to 65 ft·lb. Which tool lets a mechanic tighten them to that specified value?

    1. AImpact wrench
    2. BTorque wrench
    3. CBreaker bar
    4. DBox-end wrench
    Show answer and explanation

    Answer: B. A torque wrench measures the twisting force applied to a bolt and shows or signals when the set value, such as 65 ft·lb, is reached.

    • AWrong. An impact wrench hammers bolts tight quickly but does not measure the force, so it easily overtightens.
    • BCorrect. A torque wrench reads or clicks at a set twisting force, so the bolts reach the value the manual gives.
    • CWrong. A breaker bar is a long handle for loosening tight bolts; it gives leverage but no reading of the force.
    • DWrong. A box-end wrench grips the bolt well but gives no measure of how tight it is.
  6. In the engine shown, which number points to the connecting rod?

    12345
    1. A2
    2. B3
    3. C4
    4. D5
    Show answer and explanation

    Answer: C. The connecting rod (4) joins the piston (3) to the crankshaft (5). It carries the push of combustion down to the crank and turns it.

    • AWrong. 2 points to a valve in the cylinder head, which opens and closes to let gases in or out.
    • BWrong. 3 points to the piston, which slides in the cylinder and is pushed down by combustion.
    • CCorrect. 4 points to the connecting rod, the link between the piston pin and the crankshaft.
    • DWrong. 5 points to the crankshaft, the part the connecting rod turns.
  7. On many front suspensions, which part joins the control arm to the steering knuckle, letting the wheel both steer and move up and down?

    1. ATie rod end
    2. BWheel bearing
    3. CBall joint
    4. DSway bar link
    Show answer and explanation

    Answer: C. A ball joint is a ball-and-socket pivot between the control arm and the steering knuckle. It lets the knuckle turn for steering while the suspension moves up and down.

    • AWrong. The tie rod end connects the steering linkage to the knuckle's steering arm; it pushes the wheel to steer but does not attach the control arm.
    • BWrong. The wheel bearing lets the wheel spin on the knuckle or spindle; it does not connect the control arm.
    • CCorrect. A ball joint links the control arm to the knuckle and pivots in every direction, so the wheel can steer and move up and down.
    • DWrong. A sway bar link connects the anti-roll bar to the suspension to reduce body lean, not the control arm to the knuckle.
  8. What is the main job of an engine's timing belt or timing chain?

    1. AKeep the camshaft in step with the crankshaft
    2. BDrive the alternator and power steering pump
    3. CCarry power from the engine to the transmission
    4. DTurn the radiator fan when the engine runs hot
    Show answer and explanation

    Answer: A. The timing belt or chain links the crankshaft to the camshaft so the valves open and close at the right moments in each piston's stroke.

    • ACorrect. The timing belt or chain locks the camshaft to the crankshaft so the valves open and close in step with the pistons.
    • BWrong. The accessory (serpentine) belt drives the alternator and power steering pump, not the timing belt.
    • CWrong. Power goes from the engine to the transmission through the flywheel and clutch or torque converter, not a timing belt.
    • DWrong. The radiator fan is driven by an electric motor or by the accessory belt, not by the timing belt.
  9. Where is the car maker's recommended tire pressure for a car usually listed?

    1. AOn the tire's sidewall
    2. BOn the radiator cap
    3. COn the driver's door jamb
    4. DOn the valve stem cap
    Show answer and explanation

    Answer: C. Car makers list the recommended cold tire pressure on a placard, usually on the driver's door jamb, and in the owner's manual.

    • AWrong. The pressure on the sidewall is the tire's maximum safe pressure, not the pressure recommended for the car.
    • BWrong. The number on a radiator cap is the cooling system pressure it holds, not a tire pressure.
    • CCorrect. The tire placard on the driver's door jamb gives the car maker's recommended cold pressure for that car.
    • DWrong. A valve stem cap only keeps dirt and moisture out of the valve; it carries no pressure rating.
  10. An engine keeps losing coolant with no leak visible outside, and its exhaust gives off thick white smoke with a sweet smell. What is the most likely cause?

    1. AWorn piston rings
    2. BA thermostat stuck open
    3. CA leaking head gasket
    4. DToo rich a fuel mixture
    Show answer and explanation

    Answer: C. A leaking head gasket can let coolant seep into a cylinder, where it is burned. That uses up coolant without an outside leak and makes sweet-smelling white exhaust smoke.

    • AWrong. Worn piston rings let oil into the cylinders, which gives blue-gray smoke and oil loss, not coolant loss.
    • BWrong. A thermostat stuck open makes the engine slow to warm up; it does not burn coolant or make white smoke.
    • CCorrect. Coolant leaking past the head gasket into a cylinder is burned with the fuel, so coolant disappears and the exhaust turns white and sweet-smelling.
    • DWrong. A rich fuel mixture gives black, sooty smoke and a fuel smell, and it does not use up coolant.

Shop Information: 10 questions

Tools, fasteners, measuring, and shop practices. Real test: 10 questions in 6 minutes.

  1. Which tool is used to mark a line straight across the face of a board at a right angle to its edge?

    1. AChalk line
    2. BMarking gauge
    3. CPlumb bob
    4. DTry square
    Show answer and explanation

    Answer: D. A try square has a blade fixed at 90° to its handle. With the handle held against the board's edge, the blade guides a pencil line square across the face.

    • AWrong. A chalk line snaps a long straight line between two marked points; it does not set a right angle to an edge.
    • BWrong. A marking gauge scribes a line parallel to an edge, not across the board at a right angle.
    • CWrong. A plumb bob hangs on a string to find true vertical; it is not used to mark across a board.
    • DCorrect. A try square's blade is fixed at 90° to its handle, so holding the handle on the edge lets you draw a line square across the face.
  2. Which of these woods is a softwood?

    1. AOak
    2. BMaple
    3. CWalnut
    4. DPine
    Show answer and explanation

    Answer: D. Softwoods come from conifers, cone-bearing trees with needles. Pine is a conifer, so it is a softwood.

    • AWrong. Oak comes from a broadleaf tree that drops its leaves, so it is a hardwood.
    • BWrong. Maple comes from a broadleaf tree, so it is a hardwood.
    • CWrong. Walnut comes from a broadleaf tree, so it is a hardwood.
    • DCorrect. Pine is a needle-bearing conifer, and lumber from conifers is called softwood.
  3. Which nail is made for attaching trim and molding, with a small head that can be sunk below the wood surface and hidden with filler?

    1. AFinishing nail
    2. BCommon nail
    3. CRoofing nail
    4. DDuplex nail
    Show answer and explanation

    Answer: A. A finishing nail has a small, barrel-shaped head that can be driven just below the surface and covered, so it is used where the nail should not show.

    • ACorrect. A finishing nail's small head can be set below the surface and filled over, which suits trim and molding.
    • BWrong. A common nail has a wide, flat head for framing strength; the head stays visible and is hard to hide.
    • CWrong. A roofing nail has an extra-wide head to hold shingles and roofing felt down; it is meant to grip, not to be hidden.
    • DWrong. A duplex nail has two heads so it can be pulled out easily, which is why it is used for temporary work such as concrete forms.
  4. A carpenter drills a pilot hole before driving a wood screw near the end of a board. What is the main reason?

    1. ATo keep the wood from splitting
    2. BTo make the joint watertight
    3. CTo let the screw head sit below the surface
    4. DTo keep the board from warping
    Show answer and explanation

    Answer: A. A pilot hole makes room for the screw's shank, so the screw does not wedge the wood fibers apart and split the board, especially near an end or edge.

    • ACorrect. A pilot hole gives the screw a path, so it does not force the fibers apart and split the board near its end.
    • BWrong. A pilot hole does nothing to seal a joint; keeping water out takes glue, caulk or a finish.
    • CWrong. Setting a screw head below the surface takes a countersink or counterbore, not a plain pilot hole.
    • DWrong. Warping comes from uneven drying and moisture in the wood; a pilot hole does not prevent it.
  5. What is the main purpose of a flat washer under a nut?

    1. ATo cut threads in the hole as the nut turns
    2. BTo hold two boards at a right angle
    3. CTo spread the load of the nut over a wider area
    4. DTo let the bolt be driven like a nail
    Show answer and explanation

    Answer: C. A flat washer spreads the clamping force over a larger surface, protecting the material and helping keep the joint tight.

    • AWrong. Threads in a hole are cut with a tap, not a washer.
    • BWrong. Holding boards at right angles is the job of brackets, clamps, or joinery.
    • CCorrect. A flat washer spreads the nut’s clamping force over a wider area, protecting the surface and helping the joint stay tight.
    • DWrong. Bolts are threaded fasteners turned with a wrench; a washer does not change that.
  6. Which drill bit should be used to drill a hole in concrete?

    1. ASpade bit
    2. BBrad-point bit
    3. CCarbide-tipped masonry bit
    4. DForstner bit
    Show answer and explanation

    Answer: C. Masonry bits have hard carbide tips that can grind through concrete and brick, often in a hammer drill. The other bits are made for wood.

    • AWrong. A spade bit is a flat paddle for boring large holes in wood.
    • BWrong. A brad-point bit has a sharp center spur for clean holes in wood.
    • CCorrect. A masonry bit has a hard carbide tip that grinds through concrete and brick, often in a hammer drill.
    • DWrong. A Forstner bit bores clean, flat-bottomed holes in wood.
  7. The wood joint shown is a

    1. ABox joint
    2. BMortise-and-tenon joint
    3. CRabbet joint
    4. DDovetail joint
    Show answer and explanation

    Answer: D. Flared, wedge-shaped tails on one board lock into matching sockets in the other. That is a dovetail joint, which resists being pulled apart.

    • AWrong. A box (finger) joint uses straight, square fingers of equal width, not flared ones.
    • BWrong. A mortise-and-tenon joint has one rectangular tenon fitted into a hole, not a row of interlocking pieces.
    • CWrong. A rabbet joint fits one board into an L-shaped step cut along the edge or end of another.
    • DCorrect. The tails widen toward their ends and lock into matching sockets, which keeps a dovetail joint from pulling apart.
  8. Which chisel is made to be struck with a hammer to cut through metal, such as a rusted bolt or a rivet head?

    1. AWood chisel
    2. BGouge
    3. CCold chisel
    4. DMortise chisel
    Show answer and explanation

    Answer: C. A cold chisel is a solid bar of hardened, tempered steel with a blunt cutting edge. It is driven with a hammer to cut or shear metal.

    • AWrong. A wood chisel has a thin, sharp edge for paring wood; striking metal with it chips or dulls the edge.
    • BWrong. A gouge has a curved blade for carving hollows and grooves in wood, not for cutting metal.
    • CCorrect. A cold chisel is a heavy bar of hardened steel with a blunt-angled edge, made to be hammered through metal.
    • DWrong. A mortise chisel is a thick wood chisel for chopping rectangular holes in wood; its edge is not made for steel.
  9. Which tool is used to cut threads on the outside of a metal rod so a nut can be screwed onto it?

    1. ATap
    2. BDie
    3. CReamer
    4. DCountersink
    Show answer and explanation

    Answer: B. A die, turned in a die stock (handle), cuts external threads on a rod or bolt blank.

    • AWrong. A tap cuts internal threads inside a hole, the threads a bolt screws into.
    • BCorrect. A die is turned around the outside of a rod to cut external threads, like those on a bolt.
    • CWrong. A reamer enlarges and smooths a drilled hole to an exact size; it does not cut threads.
    • DWrong. A countersink cuts a cone-shaped recess at the top of a hole so a flat-head screw sits flush.
  10. Four files are the same length but have different grades of cut. Which one removes metal fastest and leaves the roughest surface?

    1. ABastard cut
    2. BSecond cut
    3. CSmooth cut
    4. DDead smooth cut
    Show answer and explanation

    Answer: A. Among these four grades, the order from coarse to fine is bastard, second cut, smooth and dead smooth. The bastard cut has the largest, most widely spaced teeth of these, so it cuts fastest and roughest.

    • ACorrect. The bastard cut has the coarsest teeth of the four, so it removes metal fastest and leaves the roughest finish.
    • BWrong. A second cut is finer than a bastard cut; it is used after rough filing to start smoothing.
    • CWrong. A smooth cut has fine, closely spaced teeth for finishing work, so it removes metal slowly.
    • DWrong. A dead smooth cut is the finest of these grades and is used for the final, smoothest finish.

Mechanical Comprehension: 15 questions

Levers, pulleys, gears, fluids, and forces, often with a diagram. Real test: 15 questions in 22 minutes.

  1. Running hot water over a tight metal lid on a glass jar makes the lid easier to remove because

    1. Athe glass expands more than the metal lid.
    2. Bthe hot water acts like oil on the threads.
    3. Cthe heat makes the metal lid soft.
    4. Dthe metal lid expands more than the glass.
    Show answer and explanation

    Answer: D. Metal expands more than glass when heated. The lid grows slightly larger than the glass threads, which loosens its grip.

    • AWrong. If the glass grew more, the jar would press harder against the lid; glass actually expands less than metal.
    • BWrong. Water does not lubricate the threads; the lid loosens because it grows larger.
    • CWrong. Hot tap water is far too cool to soften metal; the lid gets slightly bigger, not softer.
    • DCorrect. Metal expands more than glass when heated, so the lid grows away from the glass threads and loosens.
  2. A puck slides across a level, frictionless surface after leaving the stick. If no other force acts on it, what happens to the puck?

    1. AIt keeps moving at the same speed and direction.
    2. BIt slows down gradually and stops.
    3. CIt speeds up for a short time.
    4. DIt curves off to one side.
    Show answer and explanation

    Answer: A. An object in motion keeps the same speed and direction unless a force acts on it (inertia, Newton's first law).

    • ACorrect. With no force acting, nothing changes its motion, so it keeps the same speed and direction.
    • BWrong. Slowing down needs a force such as friction, and here there is none.
    • CWrong. Speeding up needs a push in the direction of motion; the stick is no longer touching it.
    • DWrong. Curving needs a sideways force, and no force acts on the puck.
  3. A loaded boat floats at rest on a lake. How does the weight of the water the boat pushes aside compare with the weight of the boat and its load?

    1. AIt is less than the weight of the boat and load.
    2. BIt is equal to the weight of the boat and load.
    3. CIt is greater than the weight of the boat and load.
    4. DIt depends on how deep the lake is.
    Show answer and explanation

    Answer: B. A floating object sinks until it pushes aside water equal to its own weight. That water's weight is the buoyant force holding the boat up.

    • AWrong. If less water were pushed aside, the buoyant force would be smaller than the weight and the boat would sink lower.
    • BCorrect. A floating object displaces its own weight of water, so the buoyant force exactly balances the boat and load.
    • CWrong. If more water were pushed aside, the buoyant force would exceed the weight and push the boat higher until they matched.
    • DWrong. Lake depth does not matter; only the weight of the displaced water does.
  4. A bicycle's front sprocket has 48 teeth and its rear sprocket has 16 teeth. The rider turns the pedals at 60 rpm. How fast does the rear wheel turn?

    1. A20 rpm
    2. B60 rpm
    3. C120 rpm
    4. D180 rpm
    Show answer and explanation

    Answer: D. The chain moves the same number of teeth past each sprocket. Each pedal turn moves 48 teeth, which turns the 16-tooth rear sprocket 48 ÷ 16 = 3 times, so 60 × 3 = 180 rpm.

    • AWrong. 20 rpm divides by 3 instead of multiplying; the smaller rear sprocket turns faster than the front one, not slower.
    • BWrong. 60 rpm assumes the chain makes both sprockets turn at the same speed, but they have different numbers of teeth.
    • CWrong. 120 rpm doubles the pedal speed, but the tooth ratio is 48 to 16, which is 3 to 1, not 2 to 1.
    • DCorrect. One pedal turn pulls 48 teeth of chain, enough to turn the 16-tooth sprocket 3 times, so 60 × 3 = 180 rpm.
  5. In a block and tackle, four rope strands hold up the movable block and its load. Ignoring rope stretch, how far must the free end of the rope be pulled to raise the load 3 ft?

    1. A0.75 ft
    2. B3 ft
    3. C7 ft
    4. D12 ft
    Show answer and explanation

    Answer: D. Each of the four supporting strands must shorten by 3 ft, so 4 × 3 ft = 12 ft of rope is pulled through. The pulleys cut the force to one fourth but multiply the distance by four.

    • AWrong. 0.75 ft divides by the four strands; the pulleys divide the force, while the rope distance is multiplied by four.
    • BWrong. 3 ft is what a single fixed pulley needs; with four supporting strands, each one must shorten by 3 ft.
    • CWrong. 7 ft adds the 4 strands to the 3 ft lift; the strands each shorten 3 ft, so the distances multiply.
    • DCorrect. All four supporting strands shorten by 3 ft, so 4 × 3 ft = 12 ft of rope is pulled.
  6. A small gear drives a large gear that has twice as many teeth. Ignoring friction, compared with the small gear, the large gear turns

    1. Atwice as fast with half the turning force.
    2. Bhalf as fast with twice the turning force.
    3. Cat the same speed with twice the turning force.
    4. Dhalf as fast with half the turning force.
    Show answer and explanation

    Answer: B. Each turn of the small gear moves the large gear only half a turn, so it turns half as fast. Speed is traded for force, so the large gear delivers about twice the turning force (torque).

    • AWrong. A gear with more teeth turns slower than the gear driving it, not faster; this describes a large gear driving a small one.
    • BCorrect. The large gear turns once for every two turns of the small gear, so it is half as fast, and the speed lost becomes twice the turning force.
    • CWrong. Meshed gears with different numbers of teeth cannot turn at the same speed; the larger one turns slower.
    • DWrong. Without friction no work is lost, so a gear that turns slower must turn with more force, not less.
  7. A claw hammer is used to pull a nail. The nail is 2 in from the point where the hammer head rests on the board, and the hand pulls 12 in from that point. Ignoring friction, about how much force does a 30-lb pull put on the nail?

    1. A15 lb
    2. B60 lb
    3. C180 lb
    4. D360 lb
    Show answer and explanation

    Answer: C. The mechanical advantage is effort distance ÷ load distance = 12 ÷ 2 = 6, so 30 × 6 = 180 lb.

    • AWrong. 15 lb divides the pull by the 2-in distance; a lever with a long handle multiplies force.
    • BWrong. 60 lb multiplies the pull by the short 2-in distance instead of by the ratio of the distances.
    • CCorrect. 12 ÷ 2 = 6, so the 30-lb pull becomes 30 × 6 = 180 lb on the nail.
    • DWrong. 360 lb multiplies the pull by the 12-in handle distance and forgets to divide by the 2-in distance.
  8. In which of these tools is the load between the fulcrum and the effort?

    1. ASeesaw
    2. BPair of scissors
    3. CPair of tweezers
    4. DNutcracker
    Show answer and explanation

    Answer: D. A nutcracker is hinged at one end, the hand squeezes at the other end, and the nut sits in between. That makes it a second-class lever.

    • AWrong. A seesaw has the fulcrum in the middle, between the load and the effort (first class).
    • BWrong. Scissors pivot at the screw, which sits between the hand and the cutting edges (first class).
    • CWrong. Tweezers are hinged at one end with the fingers pressing in the middle, so the effort is between fulcrum and load (third class).
    • DCorrect. The nutcracker's hinge is at one end and the hand at the other, with the nut in between (second class).
  9. The net force on a cart is doubled, and at the same time the cart's mass is doubled. What happens to the cart's acceleration?

    1. AIt drops to one-fourth
    2. BIt drops to one-half
    3. CIt stays the same
    4. DIt doubles
    Show answer and explanation

    Answer: C. Acceleration equals net force divided by mass. Doubling both the top and the bottom of that fraction leaves it unchanged.

    • AWrong. One-fourth would need the force halved and the mass doubled; here the force goes up, not down.
    • BWrong. Doubling the mass alone would halve the acceleration, but the doubled force cancels that.
    • CCorrect. Acceleration is force divided by mass, so doubling both gives 2F ÷ 2m, the same value as before.
    • DWrong. Doubling the force alone would double the acceleration, but the mass doubled too.
  10. A horizontal beam rests on a support at each end, and a heavy load sits at its middle. As the beam sags, which part of it is stretched?

    1. AThe top edge
    2. BThe bottom edge
    3. CThe two ends over the supports
    4. DNo part; the whole beam is squeezed
    Show answer and explanation

    Answer: B. A beam loaded this way bends into a curve that sags downward. The material along the bottom edge is pulled longer (tension), while the top edge is squeezed (compression).

    • AWrong. The top edge is on the inside of the sag, so it is squeezed shorter (compression), not stretched.
    • BCorrect. The sagging beam curves downward, so its bottom edge becomes the outside of the curve and is pulled longer, which is tension.
    • CWrong. The ends over the supports carry the least bending; the stretching is greatest along the bottom near the middle.
    • DWrong. Only the top half is squeezed; the bottom half of a sagging beam is in tension.
  11. A worm with a single thread drives a worm wheel that has 40 teeth. The worm turns at 200 rpm. How fast does the worm wheel turn?

    1. A5 rpm
    2. B40 rpm
    3. C160 rpm
    4. D8,000 rpm
    Show answer and explanation

    Answer: A. Each full turn of a single-thread worm moves the wheel forward by one tooth, so the wheel needs 40 worm turns for one revolution: 200 ÷ 40 = 5 rpm.

    • ACorrect. A single-thread worm moves the wheel one tooth per turn, so the wheel turns 200 ÷ 40 = 5 rpm.
    • BWrong. 40 rpm uses the number of teeth as the speed; the wheel needs 40 turns of the worm to make one revolution.
    • CWrong. 160 rpm subtracts the teeth from the speed (200 − 40); gear speeds change by a ratio, not by subtraction.
    • DWrong. 8,000 rpm multiplies instead of dividing; a worm gear slows the output a great deal rather than speeding it up.
  12. In a hydraulic lift, the small piston is 2 in across and the large piston is 6 in across. A 30-lb force pushes on the small piston. Ignoring friction, how much force does the large piston push up with?

    1. A10 lb
    2. B90 lb
    3. C180 lb
    4. D270 lb
    Show answer and explanation

    Answer: D. The pressure is the same on both pistons, so force grows with piston area. Area depends on the diameter squared: (6 ÷ 2)² = 9, and 30 × 9 = 270 lb.

    • AWrong. 10 lb divides by the size ratio; the larger piston always pushes with more force, not less.
    • BWrong. 90 lb multiplies by the diameter ratio (3), but force depends on area, which grows with the square of the diameter.
    • CWrong. 180 lb multiplies the force by the large diameter (30 × 6), which is not a pressure relationship.
    • DCorrect. The area ratio is (6 ÷ 2)² = 9, so the force is 30 × 9 = 270 lb.
  13. A hoist lifts a 550-lb crate 20 ft straight up in 10 seconds. One horsepower equals 550 ft·lb of work per second. How much power does the hoist deliver to the crate?

    1. A0.5 hp
    2. B2 hp
    3. C20 hp
    4. D200 hp
    Show answer and explanation

    Answer: B. Work = 550 lb × 20 ft = 11,000 ft·lb. Power = 11,000 ÷ 10 s = 1,100 ft·lb per second, and 1,100 ÷ 550 = 2 hp.

    • AWrong. 0.5 hp comes from swapping the distance and the time (550 × 10 ÷ 20); the work uses the 20-ft lift, then divides by the 10 seconds.
    • BCorrect. The work is 550 × 20 = 11,000 ft·lb; spread over 10 seconds that is 1,100 ft·lb per second, which is 2 hp.
    • CWrong. 20 hp treats the total work as if it were done in one second; it forgets to divide by the 10 seconds.
    • DWrong. 200 hp multiplies by the time instead of dividing; power is work divided by time.
  14. A 240-lb cart must be pushed up onto a loading dock 2 ft high. Ignoring friction, what is the shortest ramp that lets a worker do it with a push of only 60 lb along the ramp?

    1. A0.5 ft
    2. B4 ft
    3. C8 ft
    4. D16 ft
    Show answer and explanation

    Answer: C. On a frictionless ramp, force × ramp length = weight × height. So 60 lb × L = 240 lb × 2 ft, and L = 480 ÷ 60 = 8 ft.

    • AWrong. 0.5 ft flips the ratio (60 × 2 ÷ 240); a shorter ramp is steeper and needs more force, not less.
    • BWrong. 4 ft is only the force ratio 240 ÷ 60; that ratio has to be multiplied by the 2-ft height.
    • CCorrect. Force × length must equal weight × height: 60 × L = 240 × 2 = 480, so L = 8 ft.
    • DWrong. 16 ft would work but is not the shortest; it doubles the 8 ft that already brings the push down to 60 lb.
  15. A 100-lb sign hangs from the middle of a cable stretched between two posts. Each half of the cable makes a 30° angle with the horizontal. What is the tension in each half of the cable?

    1. A50 lb
    2. B87 lb
    3. C100 lb
    4. D200 lb
    Show answer and explanation

    Answer: C. Each half holds up 50 lb vertically. The vertical part of the tension is T × sin 30° = T × 1/2, so T = 50 ÷ 1/2 = 100 lb.

    • AWrong. 50 lb is each half's share of the weight, but a slanted cable must pull harder than that to supply 50 lb straight up.
    • BWrong. 87 lb comes from 100 × cos 30°, which mixes up the horizontal and vertical parts of the tension.
    • CCorrect. The vertical part of each tension, T × sin 30° = T ÷ 2, must equal 50 lb, so T = 100 lb.
    • DWrong. 200 lb divides the whole 100-lb weight by sin 30° for one half, as if that half carried the entire sign.

Assembling Objects: 15 questions

Pick the figure that shows how the parts fit or connect. Real test: 15 questions in 18 minutes.

  1. Which figure best shows how the objects in the first box will look when point A is connected to point B?

    ABAB
    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: C. Point A is at a corner of the triangle and point B is at the edge of the circle. Only one choice joins exactly those two points. The shapes may be turned, which does not change where the line attaches.

    • AWrong. The line leaves the triangle at the center, but A is at a corner.
    • BWrong. The line meets the circle at the center, but B is at the edge.
    • CCorrect. The line joins a corner of the triangle (A) to the edge of the circle (B), exactly as marked. The shapes are only turned, which doesn't change where the line attaches.
    • DWrong. The line leaves the triangle at the middle of a side, but A is at a corner.
  2. Which figure best shows how the pieces in the first box will fit together?

    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: B. The loose pieces are a half and two quarters of a circle. Only one choice is cut into exactly those pieces at the same size; the others need a piece that is not in the box.

    • AWrong. This circle is cut into six sixths of a circle, but the box holds a half and two quarters of a circle.
    • BCorrect. This circle is cut into a half and two quarters of a circle: exactly the pieces in the box, at the same size.
    • CWrong. This circle is cut into two thirds and two sixths of a circle, but the box holds a half and two quarters of a circle.
    • DWrong. This circle is cut into a two-thirds piece and a one-third piece of a circle, but the box holds a half and two quarters of a circle.
  3. Which figure best shows how the objects in the first box will look when point A is connected to point B?

    ABAB
    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: B. Point A is at the edge of the circle and point B is at the middle of a side of the square. Only one choice joins exactly those two points — the shapes may be turned, which does not change where the line attaches.

    • AWrong. The line meets the square at the center, but B is at the middle of a side.
    • BCorrect. The line joins the edge of the circle (A) to the middle of a side of the square (B), exactly as marked. The shapes are only turned, which doesn't change where the line attaches.
    • CWrong. The line meets the square at a corner, but B is at the middle of a side.
    • DWrong. The line leaves the circle at the center, but A is at the edge; and the line meets the square at a corner, but B is at the middle of a side.
  4. Which figure best shows how the objects in the first box will look when point A is connected to point B?

    ABAB
    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: A. Point A is at the edge of the circle and point B is at the center of the triangle. Only one choice joins exactly those two points. The shapes may be turned, which does not change where the line attaches.

    • ACorrect. The line joins the edge of the circle (A) to the center of the triangle (B), exactly as marked. The shapes are only turned, which doesn't change where the line attaches.
    • BWrong. The line leaves the circle at the center, but A is at the edge; and the line meets the triangle at the middle of a side, but B is at the center.
    • CWrong. The line meets the triangle at the middle of a side, but B is at the center.
    • DWrong. The line meets the triangle at a corner, but B is at the center.
  5. Which figure best shows how the pieces in the first box will fit together?

    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: D. The loose pieces are two right triangles that make a rectangle. Only one choice is cut into exactly those pieces at the same size; the others need a piece that is not in the box.

    • AWrong. This rectangle is cut into four rectangles, but the box holds two right triangles.
    • BWrong. This rectangle is cut into a square and two right triangles, but the box holds two right triangles.
    • CWrong. This rectangle is cut into three right triangles, but the box holds two right triangles.
    • DCorrect. This rectangle is cut into two right triangles: exactly the pieces in the box, at the same size.
  6. Which figure best shows how the pieces in the first box will fit together?

    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: D. The loose pieces are two rectangles that make a square. Only one choice is cut into exactly those pieces at the same size; the others need a piece that is not in the box.

    • AWrong. This square is cut into four right triangles, but the box holds two rectangles.
    • BWrong. This square is cut into four squares, but the box holds two rectangles.
    • CWrong. This square is cut into a rectangle and two right triangles, but the box holds two rectangles.
    • DCorrect. This square is cut into two rectangles: exactly the pieces in the box, at the same size.
  7. Which figure best shows how the objects in the first box will look when point A is connected to point B?

    ABAB
    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: C. Point A is at a corner of the square and point B is at the center of the circle. Only one choice joins exactly those two points. The shapes may be turned, which does not change where the line attaches.

    • AWrong. The line meets the circle at the edge, but B is at the center.
    • BWrong. The line leaves the square at the middle of a side, but A is at a corner; and the line meets the circle at the edge, but B is at the center.
    • CCorrect. The line joins a corner of the square (A) to the center of the circle (B), exactly as marked. The shapes are only turned, which doesn't change where the line attaches.
    • DWrong. The line leaves the square at the middle of a side, but A is at a corner.
  8. Which figure best shows how the pieces in the first box will fit together?

    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: A. The loose pieces are three triangles that make a triangle. Only one choice is cut into exactly those pieces at the same size; the others need a piece that is not in the box.

    • ACorrect. This triangle is cut into three triangles: exactly the pieces in the box, at the same size.
    • BWrong. This triangle is cut into an equilateral triangle and a trapezoid, but the box holds three triangles.
    • CWrong. This triangle is cut into two right triangles, but the box holds three triangles.
    • DWrong. This triangle is cut into four equilateral triangles, but the box holds three triangles.
  9. Which figure best shows how the pieces in the first box will fit together?

    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: D. The loose pieces are four quarters of a circle. Only one choice is cut into exactly those pieces at the same size; the others need a piece that is not in the box.

    • AWrong. This circle is cut into two thirds and two sixths of a circle, but the box holds four quarters of a circle.
    • BWrong. This circle is cut into a half, a third, and a sixth of a circle, but the box holds four quarters of a circle.
    • CWrong. This circle is cut into a half and two quarters of a circle, but the box holds four quarters of a circle.
    • DCorrect. This circle is cut into four quarters of a circle: exactly the pieces in the box, at the same size.
  10. Which figure best shows how the pieces in the first box will fit together?

    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: D. The loose pieces are a two-thirds piece and a one-third piece of a circle. Only one choice is cut into exactly those pieces at the same size; the others need a piece that is not in the box.

    • AWrong. This circle is cut into a three-quarter piece and a one-quarter piece of a circle, but the box holds a two-thirds piece and a one-third piece of a circle.
    • BWrong. This circle is cut into two halves of a circle, but the box holds a two-thirds piece and a one-third piece of a circle.
    • CWrong. This circle is cut into three thirds of a circle, but the box holds a two-thirds piece and a one-third piece of a circle.
    • DCorrect. This circle is cut into a two-thirds piece and a one-third piece of a circle: exactly the pieces in the box, at the same size.
  11. Which figure best shows how the objects in the first box will look when point A is connected to point B?

    ABAB
    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: D. Point A is at the widest corner of the parallelogram and point B is at a corner of the rectangle. Only one choice joins exactly those two points — the shapes may be turned, which does not change where the line attaches.

    • AWrong. The line leaves the parallelogram at the sharpest corner, but A is at the widest corner.
    • BWrong. The line meets the rectangle at the center, but B is at a corner.
    • CWrong. The line meets the rectangle at the middle of the shortest side, but B is at a corner.
    • DCorrect. The line joins the widest corner of the parallelogram (A) to a corner of the rectangle (B), exactly as marked. The shapes are only turned, which doesn't change where the line attaches.
  12. Which figure best shows how the objects in the first box will look when point A is connected to point B?

    ABAB
    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: C. Point A is at the center of the kite and point B is at a corner of the rectangle. Only one choice joins exactly those two points. The shapes may be turned, which does not change where the line attaches.

    • AWrong. The line leaves the kite at the middle of the shortest side, but A is at the center.
    • BWrong. The line leaves the kite at the 81° corner, but A is at the center.
    • CCorrect. The line joins the center of the kite (A) to a corner of the rectangle (B), exactly as marked. The shapes are only turned, which doesn't change where the line attaches.
    • DWrong. The line leaves the kite at the sharpest corner, but A is at the center.
  13. Which figure best shows how the objects in the first box will look when point A is connected to point B?

    ABAB
    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: C. Point A is at the widest corner of the parallelogram and point B is at the middle of the shortest side of the parallelogram. Only one choice joins exactly those two points. The shapes may be turned, which does not change where the line attaches.

    • AWrong. The line leaves the parallelogram at the middle of the longest side, but A is at the widest corner.
    • BWrong. The line meets the parallelogram at the middle of the longest side, but B is at the middle of the shortest side.
    • CCorrect. The line joins the widest corner of the parallelogram (A) to the middle of the shortest side of the parallelogram (B), exactly as marked. The shapes are only turned, which doesn't change where the line attaches.
    • DWrong. The line leaves the parallelogram at the sharpest corner, but A is at the widest corner.
  14. Which figure best shows how the pieces in the first box will fit together?

    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: D. The loose pieces are two trapezoids that make a hexagon. Only one choice is cut into exactly those pieces at the same size; the others need a piece that is not in the box.

    • AWrong. This hexagon is cut into a triangle and a five-sided piece, but the box holds two trapezoids.
    • BWrong. This hexagon is cut into two triangles and a rectangle, but the box holds two trapezoids.
    • CWrong. This hexagon is cut into three diamonds, but the box holds two trapezoids.
    • DCorrect. This hexagon is cut into two trapezoids: exactly the pieces in the box, at the same size.
  15. Which figure best shows how the objects in the first box will look when point A is connected to point B?

    ABAB
    1. A
    2. B
    3. C
    4. D
    Show answer and explanation

    Answer: A. Point A is at the corner of the kite where the two short sides meet and point B is at the center of the hexagon. Only one choice joins exactly those two points. The shapes may be turned, which does not change where the line attaches.

    • ACorrect. The line joins the corner of the kite where the two short sides meet (A) to the center of the hexagon (B), exactly as marked. The shapes are only turned, which doesn't change where the line attaches.
    • BWrong. The line leaves the kite at the sharpest corner, but A is at the corner where the two short sides meet.
    • CWrong. The line leaves the kite at the middle of the longest side, but A is at the corner where the two short sides meet.
    • DWrong. The line meets the hexagon at the middle of a side, but B is at the center.
The ASVAB Practice Exams team

Built and maintained by the ASVAB Practice Exams team. Every question is original, written to a subtest blueprint drawn from the official samples and DoD technical reports, and checked by a second reviewer who answers it without the key. About this site →